Description: Referring incorrect memory Incorrect command Finished due to error inside Qt library Finished due to error outside Qt library Program forced to stop. Detection timing Error occurred with the process inside the MFP controller
Causes: MFP board (MFPB)
Remedy: 1 Check the connectors on MFPB for proper connection and correct as necessary. 2 Replace MFPB 3 Acquire the debug logs in [Service Mode] -> [Debug Settings] and analyze them.
Code: CED01
Description: The authentication application information does not exist in the hard disk/SSD board in the enhanced server authentication state. With “Enhanced Server Authentication” set, no authentication application registration information is found in the hard disk or the SSD board (SSDB).
Causes: • SSD board (SSDB) • Hard disk
Remedy: 1 Turn OFF the main power switch, wait for 10 sec. or more, and turn ON the main power switch. 2 Check the connector from MFPB to Hard disk for proper connection and correct as necessary. 3 Check the connector from SSDB to MFPB for proper connection and correct as necessary. 4 Logically format the hard disk. 5 Replace the hard disk 6 If the above actions do not solve the problem, contact KM.
Code: CEEE1
Description: MFP board malfunction. MFP board (MFPB) is faulty
Causes: MFP board (MFPB)
Remedy: 1 Check the connectors on MFPB for proper connection and correct as necessary. 2 Replace MFPB
Code: CEEE2
Description: Scanner section malfunction. A scanner part is faulty.
Causes: • LED exposure unit (LU201) • CCD board (CCDB) • Scanner drive board (SCDB)
Remedy: 1 Correct the connector connection between CCDB and SCDB if faulty. 2 Replace SCDB 3 Replace CCDB
Code: CEEE3
Description: Printer control board malfunction. Printer control board (PRCB) is faulty.
Causes: Printer control board (PRCB)
Remedy: 1 Check the PRCB connector for proper connection and correct as necessary. 2 Replace PRCB
Remedy: 1 Main power switch Turn OFF and ON the main power switch, and check if the Abort code appears again. NO When not reappearing, continuous use is carried out, and it is checked whether an abort code occurs. 2 Connector connection Check the connector for proper connection and correct as necessary. • MFP board (MFPB) • Memory board/1 (Standard memory: MEMB/1) • Memory board/2 (Expansion memory: MEMB/2) • Dual scan image processing board (DSIPB) • DSC board/1 (DSCB/1: SC-508) • DSC board/2 (DSCB/2: SC-508) • Hard disc (HDD) NO It will correct, if connector connection has abnormalities. 3 Firmware Update the firmware to the latest version, and check if the Abort code appears again. NO After conducting firmware updating, check the firmware version No. and confirm that the firmware has been normally updated. 4 Memory Check Conduct the following setting. [Service Mode] -> [State Confirmation] -> [Memory/ HDD Adj.] -> [Memory Check] -> [Rough Check]. NO When "NG" is displayed, replace the appropriate memory or PWB. • WORK0: Standard memory (MEMB/1) • WORK1: Expansion memory (MEMB/2) • FILE0,1: MFP board (MFPB) • FILE2,3: not used • FILE4,5: Dual scan image processing board (DSIPB) 5 HDD R/W Check Conduct the following setting. [Service Mode] -> [State Confirmation] -> [Memory/ HDD Adj.] -> [HDD R/W Check]. NO When "NG" is displayed, replace the hard disk (HDD). 6 JPEG Check Conduct the following setting. [Service Mode] -> [State Confirmation] -> [Memory/ HDD Adj.] -> [JPEG Check]. NO When "NG" is displayed, Check the MFPB. 7 MFP board Replace MFPB NO Other electric parts indicated to Component of abort code list are replaceed.