Xerox Phaser 6510
Error Codes List page 11
|
|
- Code: 058-310, 058-311, 058-315, 058-316
- Description: FUSING ASSY RAP
058-310: Fusing Ep U4 Notrdy Nc Fail
058-311: Fusing Ep U4 Notrdy Sts Fail)
058-315: FUSING ASSY HR STS Center Broken Fail
058-316: Fusing Unit HB STS Center Low Temperature Fail
059-315: FUSING ASSY HR STS Center Over Temperature Fail
Possible Parts Affected
• FUSING ASSY PL 7.1 Item 1
• Fuser Harness (DC) (J270-J272, J273) PL 18.3 Item 2 (MFP) PL 18.7 Item 2 (SFP)
• Fuser Harness (AC) 110VAC (J283-P275) PL 18.3 Item 3A (MFP) PL 18.7 Item 3A (SFP)
• Fuser Harness (AC) 220VAC(J283-P275) PL 18.3 Item 3B (MFP) PL 18.7 Item 3B (SFP)
• LV MCU Harness Assy (J280-J284) PL 18.4 Item 5 (MFP) PL 18.8 Item 5(SFP)
• LVPS Board PL 18.1 Item 16 (MFP), PL 18.5 Item 16 (SFP)
• MCU Board, PL 18.1 Item 1 (MFP), PL 18.5 Item 1 (SFP) - Remedy: 1. Verify the FUSING ASSY and the drawer connector of the printer are installed properly (without a bent pin, or any foreign or burnt objects, etc.).
2. Check the connection between the FUSING ASSY and the MCU Board and FUSING ASSY and LVPS Board (P/J283, P/J275, P/J270, and P/J273) are fully seated. (Refer to Figure 1).
3. Check the connection between the LVPS Board and the MCU Board (P/J284, P/J280) are fully seated.
4. Check the continuity between the Fuser Harness (AC) 110VAC in each cable of P/ J283<=>P/J275. • Install a new Fuser Harness (AC) 110VAC.
5. Check the continuity between the LV MCU Harness Assy (J280-J284) in each cable of P/ J284<=>P/J280. • Install a new LV MCU HARNESS ASSY PL 18.4 Item 5.
6. Install a new MCU Board, REP 18.1.1 (MFP), REP 18.5.1 (SFP)
7. Install a new LVPS Board REP 18.1.16 (MFP) REP 18.5.16 (SFP)
- Code: 059-315, 059-326, 099-396-399
- Description: FUSING ASSY RAP
059-315: FUSING ASSY HR STS Center Over Temperature Fail
059-326: FUSING ASSY HR STS Disconnection Fail
099-396: Fusing Ep U4 Noheat Center Fail
099-397: Fusing Ep U4 Slowheat Center Fail
099-398: Fusing Ep U4 Fastheat Center Fail
099-399: Fusing Ep U4 Under Side Fail
Possible Parts Affected
• FUSING ASSY PL 7.1 Item 1
• Fuser Harness (DC) (J270-J272, J273) PL 18.3 Item 2 (MFP) PL 18.7 Item 2 (SFP)
• Fuser Harness (AC) 110VAC (J283-P275) PL 18.3 Item 3A (MFP) PL 18.7 Item 3A (SFP)
• Fuser Harness (AC) 220VAC(J283-P275) PL 18.3 Item 3B (MFP) PL 18.7 Item 3B (SFP)
• LV MCU Harness Assy (J280-J284) PL 18.4 Item 5 (MFP) PL 18.8 Item 5(SFP)
• LVPS Board PL 18.1 Item 16 (MFP), PL 18.5 Item 16 (SFP)
• MCU Board, PL 18.1 Item 1 (MFP), PL 18.5 Item 1 (SFP) - Remedy: 1. Verify the FUSING ASSY and the drawer connector of the printer are installed properly (without a bent pin, or any foreign or burnt objects, etc.).
2. Check the connection between the FUSING ASSY and the MCU Board and FUSING ASSY and LVPS Board (P/J283, P/J275, P/J270, and P/J273) are fully seated. (Refer to Figure 1).
3. Check the connection between the LVPS Board and the MCU Board (P/J284, P/J280) are fully seated.
4. Check the continuity between the Fuser Harness (AC) 110VAC in each cable of P/ J283<=>P/J275. • Install a new Fuser Harness (AC) 110VAC.
5. Check the continuity between the LV MCU Harness Assy (J280-J284) in each cable of P/ J284<=>P/J280. • Install a new LV MCU HARNESS ASSY PL 18.4 Item 5.
6. Install a new MCU Board, REP 18.1.1 (MFP), REP 18.5.1 (SFP)
7. Install a new LVPS Board REP 18.1.16 (MFP) REP 18.5.16 (SFP)
- Code: 062-277, 062-311, 062-316, 062-360, 062-371, 062-380
- Description: Scanner/IIT Errors RAP
062-277:IISS-DADF Communication Fail
062-311:IISS LOGIC Fail
062-316:DADF Motor Fail
062-360:CRG Position Fail
062-371:Lamp Illumination Fail
062-380:AGC Fail
Possible Parts Affected
DADF ASSY PL 50.1 Item 1
IIT ASSY PL 50.1 Item 2
ESS Board PL 18.1 Item 5 (MFP), PL 18.5 Item 5 (SFP) - Remedy: Initial Action 1. Power down then power up the machine to check if the error recurs GP 4 . • 062-380 / 065-221/ 065-222/ 065-225 only: Clean the document glass and the white stripe before proceeding.
1. Check the connection at the ESS Board and the IIT ASSY, verify P/J1370, P/J1374 and P/ J1372 are fully seated. a. Install a new IIT ASSY REP 50.1.2
2. Check the connection at the ESS Board and the DADF ASSY, verify P/J1371 and P/ J1377 are fully seated. a. Install a new DADF ASSY REP 50.1.1 , the error persists,
3. Install a new ESS Board REP 18.1.5(MFP) REP 18.5.5(SFP)
- Code: 062-386, 062-389, 062-393, 062-396
- Description: Scanner/IIT Errors RAP
062-386:AOC Fail
062-389:CRG Over Run Fail
062-393:CCD PWBA Sync Signal Fail
062-396:CIS Cable Connection Fail
Possible Parts Affected
DADF ASSY PL 50.1 Item 1
IIT ASSY PL 50.1 Item 2
ESS Board PL 18.1 Item 5 (MFP), PL 18.5 Item 5 (SFP) - Remedy: Initial Action 1. Power down then power up the machine to check if the error recurs GP 4 . • 062-380 / 065-221/ 065-222/ 065-225 only: Clean the document glass and the white stripe before proceeding.
1. Check the connection at the ESS Board and the IIT ASSY, verify P/J1370, P/J1374 and P/ J1372 are fully seated. a. Install a new IIT ASSY REP 50.1.2
2. Check the connection at the ESS Board and the DADF ASSY, verify P/J1371 and P/ J1377 are fully seated. a. Install a new DADF ASSY REP 50.1.1 , the error persists,
3. Install a new ESS Board REP 18.1.5(MFP) REP 18.5.5(SFP)
- Code: 065-221, 065-222, 065-223, 065-224, 065-225
- Description: Scanner/IIT Errors RAP
065-221:CIS AGC Fail
065-222:CIS AOC Fail
065-223:CIS Connection Fail
065-224:CIS Device Fail
065-225:CIS FAIL
Possible Parts Affected
DADF ASSY PL 50.1 Item 1
IIT ASSY PL 50.1 Item 2
ESS Board PL 18.1 Item 5 (MFP), PL 18.5 Item 5 (SFP) - Remedy: Initial Action 1. Power down then power up the machine to check if the error recurs GP 4 . • 062-380 / 065-221/ 065-222/ 065-225 only: Clean the document glass and the white stripe before proceeding.
1. Check the connection at the ESS Board and the IIT ASSY, verify P/J1370, P/J1374 and P/ J1372 are fully seated. a. Install a new IIT ASSY REP 50.1.2
2. Check the connection at the ESS Board and the DADF ASSY, verify P/J1371 and P/ J1377 are fully seated. a. Install a new DADF ASSY REP 50.1.1 , the error persists,
3. Install a new ESS Board REP 18.1.5(MFP) REP 18.5.5(SFP)