Description: 2nd image transfer pressure /retraction failure • The state of the 2nd image transfer retraction position sensor is not changed from the unblocked to blocked state even after the lapse of a predetermined period of time during predrive. • The 2nd image transfer retraction position sensor is in the unblocked state even after the lapse of a predetermined period of time during predrive. • The 2nd image transfer retraction position sensor is not blocked (roller in the retracted position) within a predetermined period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd image transfer retraction position sensor is not unblocked (roller in the pressed position) within a predetermined period of time after the pressure sequence of the 2nd transfer roller has been started.
Causes: 2nd image transfer retraction position sensor (PS3) 2nd image transfer pressure/retraction solenoid (SD4) Transport motor (M1) Printer control board (PRCB)
Remedy: 1 Check the M1 connector for proper connection and correct as necessary. - - 2 Check M1 for proper drive coupling and correct as necessary. - - 3 Check the SD4 connector for proper connection and correct as necessary. - - 4 Check the PRCB connector for proper connection and correct as necessary. - - 5 PS3 sensor check. PRCB PJ12-3 (ON) C110: C-2 to 3 C130n: C-2 6 SD4 operation check. PRCB PJ10-6 (REM) C110: C-9 C130n: C-9 7 M1 operation check. PRCB PJ8-1 to 6 C-2 8 Change PRCB. - -
Code: 0300
Description: Polygon motor malfunction • A LOW motor lock signal is not detected even after the lapse of a predetermined period of time after the polygon motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the polygon motor remains energized.
Causes: PH unit Printer control board (PRCB)
Remedy: 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - -
Code: 0310
Description: Laser malfunction • The SOS signal is not detected within a predetermined period of time after the output of a laser has been started. • The SOS signal is never detected in the image area.
Causes: PH Unit Printer control board (PRCB)
Remedy: 1 Check the cable and connector for proper connection and correct as necessary. - - 2 Change PH unit. - - 3 Change PRCB. - -
Code: 0500
Description: Fuser warm-up failure • The thermistor does not detect a predetermined temperature value even after the lapse of a predetermined period of time after the current warm-up cycle has been started and the current warm-up cycle is thus not completed.
Causes: Fuser unit Printer control board (PRCB) DC power supply (DCPU)
Remedy: 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - -
Code: 0502
Description: Thermistor open-circuit failure • The temperature detected by the thermistor does not reach a predetermined level even after the lapse of a given period time after the warm-up cycle has been started.
Causes: Fuser unit Printer control board (PRCB) DC power supply (DCPU)
Remedy: 1 Check the fuser unit for correct installation (whether it is secured in position). - - 2 Check the fuser unit, DCPU, and PRCB for proper connection and correct as necessary. - - 3 Change fuser unit. - - 4 Change PRCB. - - 5 Change DCPU.
Code: 0503
Description: Thermistor resistance failure • The heater lamp remains ON for a predetermined consecutive period of time.
Causes: Fuser unit Printer control board (PRCB) DC power supply (DCPU)
Remedy: 1 Change fuser unit. - - 2 For C110: 1. Main switch is turned ON. 2. Open the top cover. 3. Press the following keys in this order. ROTATE TONER key -ATTENTION key - ATTENTION key - ROTATE TONER key. 4. Main switch is turned OFF/ON. For C130n: 1. Main switch is turned ON. 2. Execute [SERVICE MENU] - [FUSER UNLOCK]. See P.103 - - 3 Change PRCB. - - 4 Change DCPU. - -