PrintCopy.info service

Mimaki CG100 SRII

Error Codes List page 1

  • Code: 01
  • Display: ERR 01 MAIN ROM
  • Description: Partially damaged flash ROM data Error detected by hash check of program data in flash ROM on which the firmware is written.
  • Remedy: 1. Reinstall the firmware on the Main PCB if a debug board is available on which the original firmware is written. 2. Execute Memory Check ([#TEST] -> [ROM/RAM CHECK]) 3. Check/clear Parameters. 4. Replace the Main PCB.
  • Code: 02
  • Display: ERR 02 MAIN RAM
  • Description: Defective SD-RAM Error was detected by read/write check of the program execution area of the SDRAM on the Main PCB.
  • Remedy: 1. Reinstall the firmware on the Main PCB if a debug board is available on which the original firmware is written. 2. Execute Memory Check ([#TEST] -> [ROM/RAM CHECK]) 3. Check/clear Parameters. 4. Replace the Main PCB.
  • Code: 04
  • Display: ERR 04 FLASH ROM
  • Description: Partial damage to saved parameters (This message appears momentarily before the plotter starts normally.) An error was detected by hash check but it was corrected automatically with backup data.
  • Remedy: 1. Check the following parameters. No measures are required if in normal. • Setup parameters • Pen parameters • Communication parameters • Pointer offset • System parameters (Set parameters as needed if a problem occurs in initial state.) 2. Execute Memory Check ([#TEST] -> [ROM/RAM CHECK]) 3. Check/clear Parameters. 4. Replace the Main PCB.
  • Code: 04
  • Display: ERR 04 FLASH ROM
  • Description: Partial damage to saved parameters (This message appears momentarily and the plotter starts normally after displaying “PRMchk NG RETRY!”.) An error was detected by hash check but it was corrected by initializing the relevant parameter.
  • Remedy: 1. Check the following parameters. No measures are required if in normal. • Setup parameters • Pen parameters • Communication parameters • Pointer offset • System parameters (Set parameters as needed if a problem occurs in initial state.) 2. Execute Memory Check ([#TEST] -> [ROM/RAM CHECK]) 3. Check/clear Parameters. 4. Replace the Main PCB.
  • Code: 04
  • Display: ERR 04 FLASH ROM
  • Description: Partial damage to saved parameters (This message appears momentarily and then “RECOVER = ENTER key” appears.) An error was detected by hash check and the system is waiting for recovery operation with backup data.
  • Remedy: 1. Press [ENTER] key to restore the system to normal operation. No corrective action is needed if the plotter starts normally. Check parameters and set parameters as needed if a problem occurs in initial state. 2. Press [..] / [..] key to restore the system to normal operation. Execute the following measures if “RECOVER FAILURE” is displayed. 1)Turn power on while holding [ENTER] down to activate system parameter setting mode. 2)Write down all the system parameters. 3) Initialize the system parameters. 4) For the parameters whose values written down are normal, set those values. For the parameters whose values written down are not normal, rewrite the saved values. Alternatively, adjust the pen pressure, landing, distance compensation, right angle compensation, and make cutting position adjustment, photo-sensor adjustment, pointer offset adjustment.
  • Code: 04
  • Display: ERR 04 FLASH ROM
  • Description: Partial damage to saved parameters (The system freezes with this message displayed.) An error was detected by write data check during storage of parameters.
  • Remedy: 1. Turn power on again. No corrective action is needed if the plotter starts and works normally even after performing the same operation as was followed by the error. Perform RAM check if the same error recurs. 2. Execute the following measures if the RAM check results in “OK” since Flash ROM is assumable to be defective. 1)Update FW 2) Initialize Parameters. 3) Replace the Main PCB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Home
New Register Forgot Password?
Send message to us