Causes: The FAX processing cannot be continued due to the FAX firmware error.
Remedy: 1 Resetting the main power The FAX PWB does not operate properly. Turn off the power switch and the main power switch. After 5s passes, reinstall the FAX PWB, and then turn on the main power switch and the power switch. FAX Installation Guide 2 Firmware upgrade The firmware is faulty. Reinstall the FAX firmware. Firmware Update 3 Replacing the FAX PWB The FAX PWB is faulty. Replace the FAX PWB. FAX Installation Guide
Code: C0070
Description: FAX PWB incompatible detection error
Causes: Abnormal detection of FAX control PWB incompatibility in the initial communication with the FAX control PWB, any normal communication command is not transmitted.
Remedy: 1 Checking the FAX PWB The incompatible FAX PWB is installed. Install the FAX PWB for the applicable model. FAX Installation Guide 2 Firmware upgrade The FAX firmware is faulty. Reinstall the FAX firmware. Firmware Update 3 Replacing the main PWB The main PWB is faulty. Replace the main PWB. Detaching and reattaching the Main PWB
Code: C0080
Description: Optional Printing System device error Object: Printing System 15 (for 120V, 230V and 240V)
Causes: It is not possible to read FPGA version of the Fiery relay PWB.
Remedy: 1 Resetting the main power The EEPROM does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Replacing the Fiery relay PWB Fiery relay PWB for the other models is installed. Replace Fiery relay PWB which is applicable to the model. 3 Firmware upgrade The version of the main firmware is not supported for the fiery relay PWB. Upgrade the main firmware to the latest version. Firmware Update 4 Checking the Fiery relay PWB The connector is not connected properly. The wire or the PWB is faulty. Clean the terminal of the connectors connecting on the Fiery relay PWB and reconnect the connector. If the wire is faulty, repair or replace it. If not resolved, replace the Fiery relay PWB. 5 Checking the main PWB The connector is not connected properly. The wire or the PWB is faulty. Clean the terminal of the connector (for Fiery relay PWB) on the main PWB and reconnect. If it is not improved, replace Fiery relay PWB.
Code: C0100
Description: Backup memory device error
Causes: An abnormal status is output from the flash memory.
Remedy: 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The connector or the FFC is not connected properly. Or, the wire, FFC, the PWB is faulty. Clean the terminal of the connectors on the main PWB, reconnect the connector of the wire, and reconnect the FFC terminal. If the wire or the FFC is faulty, repair or replace them. If not resolved, replace the main PWB. Service Manual - Section 8 'PWBs' Detaching and reattaching the Main PWB
Code: C0120
Description: MAC address data error
Causes: The MAC address data is incorrect.
Remedy: 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the MAC address The MAC address is incorrect. Replace the main PWB when the MAC address is not indicated on the network status page. Detaching and reattaching the Main PWB
Code: C0130
Description: Backup memory reading/writing error
Causes: The reading or writing into the flash memory is unavailable.
Remedy: 1 Resetting the main power The flash memory does not operate properly. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the main PWB The connector or the FFC is not connected properly. Or, the wire, FFC, the PWB is faulty. Clean the terminal of the connectors on the main PWB, reconnect the connector of the wire, and reconnect the FFC terminal. If the wire or the FFC is faulty, repair or replace them. If not resolved, replace the main PWB. Service Manual - Section 8 'PWBs' Detaching and reattaching the Main PWB