PrintCopy.info service

Konica-Minolta bizhub C250i

Error Codes List page 1

  • Code: 10-01, 10-02, 10-40
  • Description: Misfeed at manual bypass paper feed section
    10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
    10-02 For paper fed from the manual bypass tray, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
    10-40 For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
  • Causes: • Transport motor (M1) • Registration clutch (CL4) • Bypass tray paper feed clutch (CL7) • Bypass tray lift-up solenoid (SD1) • Bypass tray pick-up roller solenoid (SD6) • Registration sensor (PS1) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C 3 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C 4 CL7 load check • Check code: 20 • Multi code: 3 BASEB CN26EA-12 (ON) 10-K 5 SD1 load check • Check code: 23 • Multi code: 3 BASEB CN26EA-9 (ON) 10-K 6 SD6 load check • Check code: 23 • Multi code: 3 BASEB CN26EA-7 (ON) 10-K 7 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 8 Replace BASEB.
  • Code: 11-01, 11-02
  • Description: Misfeed at tray 1 paper feed section
    11-01 After the tray 1 starts to feed paper, the registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 1 paper feed sensor (PS23). 11-02 For paper fed from the tray 1, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
  • Causes: • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Paper feed roller fast clutch (CL10) • Registration sensor (PS1) • Tray 1 paper feed sensor (PS23) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C 3 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K 4 CL3 load check • Check code: 20 • Multi code: 1 BASEB CN26EA-20 (ON) 11-K 5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C 6 CL10 load check • Check code: 20 • Multi code: 4 BASEB CN27EA-2 (ON) 13-K 7 M1 load check • Check code: 40 BASEB CN19EA-1 to 5 1-C • Multi code: 1, 4, 5 8 Replace BASEB.
  • Code: 11-05, 11-40
  • Description: Misfeed at tray 1 paper feed section
    11-05 The leading edge of the paper is not turned ON the tray 1 paper feed sensor (PS23) even after the lapse of a given period of time after the tray 1 starts to feed paper. 11-40 For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
  • Causes: • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Paper feed roller fast clutch (CL10) • Registration sensor (PS1) • Tray 1 paper feed sensor (PS23) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C 3 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K 4 CL3 load check • Check code: 20 • Multi code: 1 BASEB CN26EA-20 (ON) 11-K 5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C 6 CL10 load check • Check code: 20 • Multi code: 4 BASEB CN27EA-2 (ON) 13-K 7 M1 load check • Check code: 40 BASEB CN19EA-1 to 5 1-C • Multi code: 1, 4, 5 8 Replace BASEB.
  • Code: 12-01, 12-05, 12-40
  • Description: Misfeed at tray 2 paper feed section
    12-01 After the tray 2 starts to feed paper, the tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 2 paper feed sensor (PS20).
    12-05 The leading edge of the paper is not turned ON the tray 2 paper feed sensor (PS20) even after the lapse of a given period of time after the tray 2 starts to feed paper.
    12-40 For paper fed from the tray 2, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 2 paper feed section results, if the tray 2 vertical transport sensor (PS19) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 2 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Transport motor (M1) • Tray 2 paper feed clutch (CL1) • Tray 2 vertical transport clutch (CL2) • Tray 2 vertical transport sensor (PS19) • Tray 2 paper feed sensor (PS20) • Base board (BASEB)
  • Remedy: 1 Initial check items - - 2 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K 3 PS20 I/O check, sensor check BASEB CN23E-5 (ON) 15-K 4 CL1 load check • Check code: 20 • Multi code: 2 BASEB CN23E-16 (ON) 16-K 5 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K 6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19EA-1 to 5 1-C 7 Replace BASEB.
  • Code: 13-01, 13-05, 13-40
  • Description: Misfeed at tray 3 paper feed section
    13-01 After the tray 3 starts to feed paper, the tray 3 vertical transport sensor (PS113) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 3 paper feed sensor (PS112).
    13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS112) even after the lapse of a given period of time after the tray 3 starts to feed paper.
    13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 3 paper feed section results, if the tray 3 vertical transport sensor (PS113) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 3 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Tray 3 paper feed motor (M111) • Tray 3 vertical transport motor (M112) • Tray 3 paper feed sensor (PS112) • Tray 3 vertical transport sensor (PS113) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 PS112 I/O check, sensor check PCCB CN4-11 (ON) PC-116/PC-216 5 to 6-C 3 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-116/PC-216 5-C 4 M111 load check • Check code: 28 • Multi code: 11, 14, 15 PCCB CN5-1 to 8 PC-116/PC-216 4-C 5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-116/PC-216 3 to 4-C 6 Replace PCCB.
  • Code: 14-01, 14-05, 14-40
  • Description: Misfeed at tray 4 paper feed section
    14-01 After the tray 4 starts to feed paper, the tray 4 vertical transport sensor (PS123) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 4 paper feed sensor (PS122).
    14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS122) even after the lapse of a given period of time after the tray 4 starts to feed paper.
    14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
    - Paper jam of a sheet of paper left at the tray 4 paper feed section results, if the tray 4 vertical transport sensor (PS123) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
    - Paper jam of a sheet of paper left at the tray 4 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
  • Causes: • Tray 4 paper feed motor (M121) • Tray 4 vertical transport motor (M122) • Tray 4 paper feed sensor (PS122) • Tray 4 vertical transport sensor (PS123) • PC control board (PCCB)
  • Remedy: 1 Initial check items - - 2 PS122 I/O check, sensor check PCCB CN18C-2 (ON) PC-216 7-K 3 PS123 I/O check, sensor check PCCB CN18C-5 (ON) PC-216 7-K 4 M121 load check • Check code: 28 • Multi code: 16, 19, 20 PCCB CN9C-1 to 8 PC-216 6-K 5 M122 load check • Check code: 28 • Multi code: 26, 29, 30 PCCB CN9C-9 to 16 PC-216 6-K 6 Replace PCCB.
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Home
New Register Forgot Password?
Send message to us