Konica-Minolta bizhub 750i
Error Codes List page 1
|
- Code: 10-01, 10-02, 10-04, 10-40
- Description: Misfeed at manual bypass paper feed section
10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
10-02 For paper fed from the manual bypass tray, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
10-04 The leading edge of the paper is not turned ON the registration sensor/2 (PS72) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
10-40 For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. - Causes: • Paper feed motor (M22)
• Registration motor (M24)
• Bypass tray paper feed clutch (CL7)
• Bypass tray lift-up solenoid (SD1)
• Bypass tray pick-up roller solenoid (SD6)
• Registration sensor/1 (PS1)
• Registration sensor/2 (PS72)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS72 I/O check, sensor check BASEB CN15E-19 (ON) 5-C
4 CL7 load check • Check code: 20 • Multi code: 3
BASEB CN26EA-12 (ON) 10-K
5 SD1 load check • Check code: 23 • Multi code: 3
BASEB CN26EA-9 (ON) 10-K
6 SD6 load check • Check code: 23 • Multi code: 3
BASEB CN26EA-7 (ON) 10-K
7 M22 load check • Check code: 28 • Multi code: 31, 34, 35
BASEB CN31E-1 to 4 23-K
8 M24 load check • Check code: 26 • Multi code: 1, 4, 5
BASEB CN31E-9 to 12 24-K
9 Replace BASEB.
- Code: 11-01, 11-02, 11-04
- Description: Misfeed at tray 1 paper feed section
11-01 After the tray 1 starts to feed paper, the registration sensor/1 (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 1 paper feed sensor (PS23).
11-02 For paper fed from the tray 1, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
11-04 The leading edge of the paper is not turned ON (unblocked) the registration sensor/2 (PS72) even after the lapse of a given period of time after the tray 1 starts to feed paper.
- Paper jam of a sheet of paper left at the tray 1 paper feed section results, if the tray 1 paper feed sensor (PS23) is turned ON when operation stops due to the tray 1 FD size error. - Causes: • Paper feed motor (M22)
• Registration motor (M24)
• Registration sensor/1 (PS1)
• Tray 1 paper feed sensor (PS23)
• Registration sensor/2 (PS72)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS72 I/O check, sensor check BASEB CN15E-19 (ON) 5-C
4 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K
5 M22 load check • Check code: 28 • Multi code: 31, 34, 35
BASEB CN31E-1 to 4 23-K
6 M24 load check • Check code: 26 • Multi code: 1, 4, 5
BASEB CN31E-9 to 12 24-K
7 Replace BASEB. - -
1.5.3
- Code: 11-05, 11-40
- Description: Misfeed at tray 1 paper feed section
11-05 The leading edge of the paper is not turned ON the tray 1 paper feed sensor (PS23) even after the lapse of a given period of time after the tray 1 starts to feed paper.
11-40 For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 1 paper feed section results, if the tray 1 paper feed sensor (PS23) is turned ON when operation stops due to the tray 1 FD size error. - Causes: • Paper feed motor (M22)
• Registration motor (M24)
• Registration sensor/1 (PS1)
• Tray 1 paper feed sensor (PS23)
• Registration sensor/2 (PS72)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS72 I/O check, sensor check BASEB CN15E-19 (ON) 5-C
4 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K
5 M22 load check • Check code: 28 • Multi code: 31, 34, 35
BASEB CN31E-1 to 4 23-K
6 M24 load check • Check code: 26 • Multi code: 1, 4, 5
BASEB CN31E-9 to 12 24-K
7 Replace BASEB. - -
1.5.3
- Code: 12-01, 12-05, 12-40
- Description: Misfeed at tray 2 paper feed section
12-01 After the tray 2 starts to feed paper, the tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 2 paper feed sensor (PS20).
12-05 The leading edge of the paper is not turned ON the tray 2 paper feed sensor (PS20) even after the lapse of a given period of time after the tray 2 starts to feed paper.
12-40 For paper fed from the tray 2, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 2 paper feed section results, if the tray 2 vertical transport sensor (PS19) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 2 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Paper feed motor (M22)
• Tray 2 vertical transport motor (M23)
• Tray 2 paper feed clutch (CL1)
• Tray 2 vertical transport sensor (PS19)
• Tray 2 paper feed sensor (PS20)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
3 PS20 I/O check, sensor check BASEB CN23E-5 (ON) 15-K
4 CL1 load check
• Check code: 20
BASEB CN23E-16 (ON) 16-K • Multi code: 2
5 M22 load check • Check code: 28 • Multi code: 31, 34, 35
BASEB CN31E-1 to 4 23-K
6 M23 load check • Check code: 28 • Multi code: 36, 39, 40
BASEB CN31E-5 to 8 23-K
7 Replace BASEB. - -
- Code: 13-05, 13-40
- Description: Misfeed at tray 3 paper feed section
13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS152) even after the lapse of a given period of time after the tray 3 starts to feed paper.
13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 3 paper feed section results, if the tray 3 paper feed sensor (PS152) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M152)
• Tray 3 paper feed clutch (CL151)
• Tray 3 paper feed sensor (PS152)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS152 I/O check, sensor check PCCB CN7-2 (ON) PC-417 5-C
3 CL151 operation check PCCB CN19-1 (ON) PC-417 6-C
4 M152 load check • Check code: 28 • Multi code: 51, 52, 53, 54, 55
PCCB CN5-1 to 8 PC-417 7-K
5 Replace PCCB. - -
- Code: 14-05, 14-40
- Description: Misfeed at tray 4 paper feed section
14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS162) even after the lapse of a given period of time after the tray 4 starts to feed paper.
14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 4 paper feed section results, if the tray 4 paper feed sensor (PS162) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M152)
• Tray 4 paper feed clutch (CL161)
• Tray 4 paper feed sensor (PS162)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS162 I/O check, sensor check PCCB CN4-11 (ON) PC-417 3-C
3 CL161 operation check PCCB CN19-3 (ON) PC-417 6-C
4 M152 load check • Check code: 28 • Multi code: 51, 52, 53, 54, 55
PCCB CN5-1 to 8 PC-417 7-K
5 Replace PCCB. - -