Konica-Minolta bizhub 300i
Error Codes List page 3
|
|
- Code: 20-01, 20-02
- Description: Misfeed at vertical transport section
20-01 The registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 2 vertical transport sensor (PS19).
20-02 For paper fed from the tray 2, tray 3, tray 4, or LCT, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop. - Causes: • Transport motor (M1)
• Tray 2 vertical transport clutch (CL2)
• Registration clutch (CL4)
• Document registration sensor (PS1)
• Tray 2 vertical transport sensor (PS19)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K
5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C
6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
7 Replace BASEB.
- Code: 20-21
- Description: Misfeed at vertical transport section (tray 3)
<When PC-116 or PC-216 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 3 vertical transport sensor (PS113).
<When PC-416 is installed> The tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the vertical transport sensor (PS133).
- Paper jam of a sheet of paper left at the vertical transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: <When PC-116 or PC-216 is installed>
• Transport motor (M1)
• Tray 3 vertical transport motor (M112)
• Tray 2 vertical transport clutch (CL2)
• Tray 2 vertical transport sensor (PS19)
• Tray 3 vertical transport sensor (PS113)
• Base board (BASEB)
• PC control board (PCCB)
<When PC-416 is installed>
• Transport motor (M1)
• Vertical transport motor (M132)
• Tray 2 vertical transport clutch (CL2)
• Tray 2 vertical transport sensor (PS19)
• Vertical transport sensor (PS133)
• Base board (BASEB)
• PC control board (PCCB) - Remedy: When PC-116 or PC-216 is installed
1 Initial check items - -
2 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-116/PC-216 5-C
3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K
5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-116/PC-216 3 to 4-C
6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
7 Replace BASEB. - -
8 Replace PCCB.
When PC-416 is installed
1 Initial check items - -
2 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-416 7-J
3 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
4 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K
5 M132 load check • Check code: 28 • Multi code: 6, 9, 10 PCCB CN5-9 to 16 PC-416 4-J
6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
7 Replace BASEB. - -
8 Replace PCCB.
- Code: 20-22
- Description: Misfeed at vertical transport section (tray 4)
20-22 The tray 3 vertical transport sensor (PS113) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 4 vertical transport sensor (PS123).
- Paper jam of a sheet of paper left at the vertical transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Tray 3 vertical transport motor (M112)
• Tray 4 vertical transport motor (M122)
• Tray 3 vertical transport sensor (PS113)
• Tray 4 vertical transport sensor (PS123)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS123 I/O check, sensor check PCCB CN18-5 (ON) PC-216 7-K
3 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-216 5-C
4 M122 load check • Check code: 28 • Multi code: 26, 29, 30 PCCB CN9C-9 to 16 PC-216 6-K
5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-216 3 to 4-C
6 Replace PCCB.
- Code: 30-03
- Description: Misfeed at 2nd transfer section
30-03 The fusing loop sensor (PS2) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (unblocked) the registration sensor (PS1).
- Paper jam of a sheet of paper left at the 2nd transfer section results, if the registration sensor (PS1) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the 2nd transfer section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M1)
• Registration clutch (CL4)
• Document registration sensor (PS1)
• Fusing loop sensor (PS2)
• Expansion control board (EXCB)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS2 I/O check, sensor check EXCB CN13EX-6 (ON) 4-X
4 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C
5 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
6 Replace EXCB. - -
7 Replace BASEB.
- Code: 32-01, 32-05, 32-06
- Description: Misfeed at fusing/paper exit section
32-01 The leading edge of the paper is not turned ON (unblocked) the ADU paper passage sensor/1 (PS40) even after the lapse of a given period of time after the reverse sequence is started.
32-05 The paper exit sensor (PS3) is not turned OFF (blocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (unblocked) PS3.
32-06 The paper exit sensor (PS3) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON (unblocked) the fusing loop sensor (PS2).
- Paper jam of a sheet of paper left at the paper exit section results, if the paper exit sensor (PS3) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the paper exit section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M1)
• Fusing motor (M3)
• Paper exit/reverse motor (M4)
• ADU transport motor (M5)
• Fusing loop sensor (PS2)
• Paper exit sensor (PS3)
• ADU paper passage sensor/1 (PS40)
• Exit path switch solenoid (SD3)
• Expansion control board (EXCB)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS2 I/O check, sensor check EXCB CN13EX-6 (ON) 4-X
3 PS3 I/O check, sensor check BASEB CN22E-3 (ON) 11-C
4 PS40 I/O check, sensor check BASEB CN22E-6 (ON) 11-C
5 SD3 load check • Check code: 83 • Multi code: 0 BASEB CN13E-7 (24V) 12-C
6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
7 M3 load check • Check code: 45 • Multi code: 1, 4, 5, 6 BASEB CN19E-6 to 10 1-C
8 M4 load check • Check code: 84 • Multi code: 1, 4, 5, 6, 9, 10 BASEB CN18E-3 to 6 5-C
9 M5 load check • Check code: 85 • Multi code: 1, 4, 5 BASEB CN18E-7 to 10 5-C
10 Replace EXCB. - -
11 Replace BASEB. - -
- Code: 66-01, 66-11, 66-21
- Description: Misfeed at DF turnover section
66-01 <When DF-632 is installed> The document registration sensor (PS3) is not turned ON (unblocked) even after the lapse of a given period of time after the reverse registration operation started.
66-11 <When DF-632 is installed> The document registration sensor (PS3) is not turned OFF (blocked) even after the lapse of a given period of time after PS3 has turned ON (unblocked) after the reverse registration operation started.
66-21 <When DF-632 is installed> The document reading sensor (PS4) is not turned ON even after the lapse of a given period of time after the document registration sensor (PS3) is turned ON (unblocked) after the reverse registration operation started. - Causes: • Document reading motor (M1)
• Registration motor (M3)
• Document registration sensor (PS3)
• Document reading sensor (PS4)
• DF control board (DFCB) - Remedy: 1 Initial check items - -
2 PS4 I/O check, sensor check DFCB J10-3 (ON) DF-632 2-G
3 PS3 I/O check, sensor check DFCB J14-12 (ON) DF-632 5-G
4 M1 load check • Check code: 60 • Multi code: 34, 35, 36, 37, 38, 39 DFCB J7-1 to 4 DF-632 2-B
5 M3 load check • Check code: 60 • Multi code: 17, 18, 19, 20 DFCB J6-1 to 4 DF-632 3-B
6 DFCB F6 conduction check - -
7 Replace DFCB.