Konica-Minolta bizhub 300i
Error Codes List page 1
|
- Code: 10-01, 10-02, 10-40
- Description: Misfeed at manual bypass paper feed section
10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
10-02 For paper fed from the manual bypass tray, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
10-40 For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. - Causes: • Transport motor (M1)
• Registration clutch (CL4)
• Bypass tray paper feed clutch (CL7)
• Bypass tray lift-up solenoid (SD1)
• Bypass tray pick-up roller solenoid (SD6)
• Registration sensor (PS1)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C
4 CL7 load check • Check code: 20 • Multi code: 3 BASEB CN26EA-12 (ON) 10-K
5 SD1 load check • Check code: 23 • Multi code: 3 BASEB CN26EA-9 (ON) 10-K
6 SD6 load check • Check code: 23 • Multi code: 3 BASEB CN26EA-7 (ON) 10-K
7 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
8 Replace BASEB. - -
- Code: 11-01, 11-02
- Description: Misfeed at tray 1 paper feed section
11-01 After the tray 1 starts to feed paper, the registration sensor (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 1 paper feed sensor (PS23).
11-02 For paper fed from the tray 1, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop. - Causes: • Transport motor (M1)
• Tray 1 paper feed clutch (CL3)
• Registration clutch (CL4)
• Paper feed roller fast clutch (CL10)
• Registration sensor (PS1)
• Tray 1 paper feed sensor (PS23)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K
4 CL3 load check • Check code: 20 • Multi code: 1 BASEB CN26EA-20 (ON) 11-K
5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C
6 CL10 load check • Check code: 20 • Multi code: 4 BASEB CN27EA-2 (ON) 13-K
7 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
8 Replace BASEB.
- Code: 11-05, 11-40
- Description: Misfeed at tray 1 paper feed section
11-05 The leading edge of the paper is not turned ON the tray 1 paper feed sensor (PS23) even after the lapse of a given period of time after the tray 1 starts to feed paper.
11-40 For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. - Causes: • Transport motor (M1)
• Tray 1 paper feed clutch (CL3)
• Registration clutch (CL4)
• Paper feed roller fast clutch (CL10)
• Registration sensor (PS1)
• Tray 1 paper feed sensor (PS23)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN15E-9 (ON) 4-C
3 PS23 I/O check, sensor check BASEB CN23E-2 (ON) 15-K
4 CL3 load check • Check code: 20 • Multi code: 1 BASEB CN26EA-20 (ON) 11-K
5 CL4 load check • Check code: 21 • Multi code: 2 BASEB CN15E-2 (ON) 3-C
6 CL10 load check • Check code: 20 • Multi code: 4 BASEB CN27EA-2 (ON) 13-K
7 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
8 Replace BASEB.
- Code: 12-01, 12-05, 12-40
- Description: Misfeed at tray 2 paper feed section
12-01 After the tray 2 starts to feed paper, the tray 2 vertical transport sensor (PS19) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 2 paper feed sensor (PS20).
12-05 The leading edge of the paper is not turned ON the tray 2 paper feed sensor (PS20) even after the lapse of a given period of time after the tray 2 starts to feed paper.
12-40 For paper fed from the tray 2, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 2 paper feed section results, if the tray 2 vertical transport sensor (PS19) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 2 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M1)
• Tray 2 paper feed clutch (CL1)
• Tray 2 vertical transport clutch (CL2)
• Tray 2 vertical transport sensor (PS19)
• Tray 2 paper feed sensor (PS20)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS19 I/O check, sensor check BASEB CN23E-8 (ON) 15-K
3 PS20 I/O check, sensor check BASEB CN23E-5 (ON) 15-K
4 CL1 load check • Check code: 20 • Multi code: 2 BASEB CN23E-16 (ON) 16-K
5 CL2 load check • Check code: 21 • Multi code: 1 BASEB CN23E-19 (ON) 17-K
6 M1 load check • Check code: 40 • Multi code: 1, 4, 5 BASEB CN19E-1 to 5 1-C
7 Replace BASEB. - -
- Code: 13-01, 13-05, 13-40
- Description: When PC-116 or PC-216 is installed
Misfeed at tray 3 paper feed section (When PC-116 or PC-216 is installed)
13-01 After the tray 3 starts to feed paper, the tray 3 vertical transport sensor (PS113) is not turned ON even after the lapse of a given period of time after the leading edge of the paper has turned ON the tray 3 paper feed sensor (PS112).
13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS112) even after the lapse of a given period of time after the tray 3 starts to feed paper.
13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 3 paper feed section results, if the tray 3 vertical transport sensor (PS113) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 3 paper feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Tray 3 paper feed motor (M111)
• Tray 3 vertical transport motor (M112)
• Tray 3 paper feed sensor (PS112)
• Tray 3 vertical transport sensor (PS113)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS112 I/O check, sensor check PCCB CN4-11 (ON) PC-116/PC-216 5 to 6-C
3 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-116/PC-216 5-C
4 M111 load check • Check code: 28 • Multi code: 11, 14, 15 PCCB CN5-1 to 8 PC-116/PC-216 4-C
5 M112 load check • Check code: 28 • Multi code: 21, 24, 25 PCCB CN5-9 to 16 PC-116/PC-216 3 to 4-C
6 Replace PCCB.
- Code: 13-01, 13-05, 13-40
- Description: When PC-417 is installed
Misfeed at tray 3 paper feed section (When PC-417 is installed)
13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS152) even after the lapse of a given period of time after the tray 3 starts to feed paper.
13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 3 paper feed section results, if the tray 3 paper feed sensor (PS152) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M152)
• Tray 3 paper feed clutch (CL151)
• Tray 3 paper feed sensor (PS152)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS152 I/O check, sensor check PCCB CN7-2 (ON) PC-417 5-C
3 CL151 operation check PCCB CN19-1 (ON) PC-417 6-C
4 M152 load check • Check code: 28 • Multi code: 51, 54, 55 PCCB CN5-1 to 8 PC-417 7-K
5 Replace PCCB.