KIP 7570

• Code: J-00000200
• Description: Registration Part Jam
• Causes: Registration Sensor “Delay”, “Stay”, “Early”, “Remained”
  Separation Sensor “Delay”, “Stay”, “Early”, “Remained”
• Remedy: Registration Sensor “Delay”, “Stay”, “Early”, “Remained”
  Mis-feed of paper 1 Does the paper mis-fed occur around the Registration Roller? Yes Remove the mis-fed paper.
  Registration Sensor (PH1) 2 Check the status of Registration Sensor in Input Check of the Service Mode. Signal Code : 00100 REGIST-S(Registration Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Registration Sensor. 2. Replace the Registration Sensor if there is no problem with the wire.
  Engine Unit 3 Is the Engine Unit closed firmly until it is locked? (Is the pressure around the Registration Roller correct?) No 1. Close the Engine Unit firmly. 2. Adjust the pressure around the Registration Roller.
  Driving mechanism 4 Check the operation of Registration Clutch in Output Check of the Service Mode. Device Code : 00011 REG.-CL (Registration Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Registration Clutch and Main Motor operate correctly? No Replace the Registration Clutch or Main Motor if it is defective.
  Separation Sensor “Delay”, “Stay”, “Early”, “Remained”
  Mis-feed of paper 1 Does the paper mis-fed occur around the separation area? Yes Remove the mis-fed paper.
  Separation Sensor (PH2) 2 Check the status of Separation Sensor in Input Check of the Service Mode. Signal Code : 00010 SEP-S (STRIP_S) (Separation Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Separation Sensor. 2. Replace the Separation Sensor if there is no problem with the wire.
  Transfer / Separation Corona 3 Is the Transfer / Separation Corona Unit installed to the machine correctly? Yes Install the Transfer / Separation Corona Unit correctly.
  HV Power Supply 4 Is the output from the HV Power Supply to the Separation Corona correct? No Replace the HV Power Supply.

• Code: J-04000000
• Description: Exit Part (Top) Jam
• Causes: Fuser Exit Sensor “Delay”, “Stay”, “Early”, “Remained”
• Remedy: Mis-feed of paper 1 Does the paper mis-fed occur around the fuser area? Yes Remove the mis-fed paper.
  Exit Sensor (PH3) 2 Check the status of Exit Sensor in Input Check of the Service Mode. Signal Code : 00011 EXIT-S (HEAT_EXIT) (ExitSensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Exit Sensor. 2. Replace the Exit Sensor if there is no problem with the wire.

• Code: J-08000000
• Description: Exit Part (Rear) Jam
• Causes: Exit Encoder (STACKJ_S) Sensor Jam
• Remedy: Mis-feed of paper 1 Does the paper mis-fed occur around the fuser area? Yes Remove the mis-fed paper.
  Exit Encoder (STACKJ_S) (PH16) 2 Check the status of Exit Sensor in Input Check of the Service Mode. Signal Code : 00111 EXIT-ENC (STACKJ-S) (Encoder Sensor (Exit)) Does the status change “L” and “H” when the paper feeds? No 1. Check if there is any problem with the wire connected to the Encoder sensor (Exit). 2. Replace the Encoder Sensor (Exit) if there is no problem with the wire.

• Code: J-10000000
• Description: Stacker Jam
• Causes: Optional Device Jam “Delay”, “Stay”
• Remedy: Installation Position 1 Is the distance between the printer and the optional device not appropriate (too far away)? Yes Install it correctly.
  Mis-feed of paper 2 Does the paper mis-fed occur in the optional device? Yes Remove the mis-fed paper
  Sensor in the optional device 3 Under the sensor detects the media, turn off/on the printer. Does “Stacker Jam (J-10000000)” occur? No 1. Check if there is any problem with the wire connected to the sensor. 2. Replace the sensor if there is no problem with the wire.