PrintCopy.info service

Canon D550

Error Codes List page 1

  • Code: E000-0000
  • Description: Fixing Assembly does not start up within specified time.
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.
    [1] 100 V machine - Heater resistance: 12.9 U ±7%
    [2] 120 V machine - Heater resistance: 16.0 U ±7%
    [3] 230 V machines - Heater resistance: 53.8 U ±7%
    (2) Check the connection of connector (J101) on the Engine Controller Board.
    (3) Check the connection of connector (J552) on Engine Controller Board.
    (4) Replace the Fixing Assembly. (5) Replace the Engine Controller Board.
  • Code: E001-0000
  • Description: Abnormally high temperature (detected by main thermistor)
    The main thermistor detected an abnormally high temperature 235 deg C) during temperature control
  • Remedy: - When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.
    [1] 100 V machine - Heater resistance: 12.9 U ±7%
    [2] 120 V machine - Heater resistance: 16.0 U ±7%
    [3] 230 V machines - Heater resistance: 53.8 U ±7%
    (2) Check the connection of connector (J101) on the Engine Controller Board.
    (3) Check the connection of connector (J552) on Engine Controller Board.
    (4) Replace the Fixing Assembly.
    (5) Replace the Engine Controller Board.
  • Code: E003-0000
  • Description: Abnormal low-temperature detection
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.
    [1] 100 V machine - Heater resistance: 12.9 U ±7%
    [2] 120 V machine - Heater resistance: 16.0 U ±7%
    [3] 230 V machines - Heater resistance: 53.8 U ±7%
    (2) Check the connection of connector (J101) on the Engine Controller Board.
    (3) Check the connection of connector (J552) on Engine Controller Board.
    (4) Replace the Fixing Assembly.
    (5) Replace the Engine Controller Board.
  • Code: E004-0000
  • Description: Fixing power supply drive circuit error
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Replace the Engine Controller Board.
    (2) Replace the Fixing Assembly.
  • Code: E100-0001
  • Description: Error detection on any of scanner motor, laser unit, and BD detection at scanner area.
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Replace the Laser Scanner Unit.
    (2) Replace the Engine Controller Board.
  • Code: E196-2000
  • Description: ROM read/write error (Error in storing each setting values for user mode / service mode / factory mode)
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Update the set of the Controller Firmware
    (2) Replace the Main Controller Board.
  • Code: E202-0002
  • Description: Contact Sensor HP error, Failure in return
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.
    (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.
    (3) Replace the Contact Sensor.
    (4) Replace the Main Controller Board.
  • Code: E225-0001
  • Description: Light intensity of a lamp is less or equal to the criteria
  • Remedy: When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.
    (1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.
    (2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.
    (3) Replace the Contact Sensor. (4) Replace the Main Controller Board.
Service manual
Error Code
Parts Catalog
Compatibility
Home
New Register Forgot Password?
Send message to us