Description: Data transmission to the PC failed in buffer dumping
Causes: Data transmission was attempted but the PC was not ready for receiving after 10 seconds. 1) The cable is not compatible. 2) Malfunction in the main PCB assembly. 3) RS-232C cable is not connected. 4) The port is occupied or otherwise closed by an application in the host PC side.
Remedy: 1) Change to a genuine cable. 2) Perform a loop-back test. If the error persists, replace the main PCB assembly. 3) Connect a cable (genuine cable is recommended). 4) Shut all applications in the host side so that dump data reception from the plotter is the only active application.
Code: 26
Display: ERR 26 I/F T26EST n
Description: Error in a loop-back test
Causes:
Remedy: Disconnect a lip-back connector. Attach the loop-back connector and perform the test. Malfunction in the main PCB assembly. n=1:RS-CD loop fault n=2:ER-CS, DR loop fault n=3:TX time-out n=4:Conveyor error (data jam) n=5:Error interruption detected. Suspect defective PCB assembly such as a broken wire and a defective serial controller built into the CPU. Replace the main PCB assembly.
Code: 27
Display: ERR 27 BUFFERover
Description: Data receiving buffer overflow
Causes:
Remedy: Handshake setting is incorrect (if RS-232C interface is used). 1. Check the application in the host PC side or the handshake setting in the plotter driver side. Match the plotter communication condition settings. 2. Switch to the USB interface. The cable is not compatible for hardware handshake. 1. Change to a genuine cable. 2. Check the cable for broken wire or short circuits. Handshake failure due to a malfunction of the main PCM assembly. Attach the loop-back connector and perform handshake test. If the error persists, replace the main PCB assembly (if RS-232C interface is used).
Code: 30
Display: ERR 30 OPERATION
Description: Illegal operation was attempted
Causes: Errorneous operation has been performed. 1) The attempted origin falls outside of the cutting area. 2) The origin will fall outside of the attempted cutting area. 3) The attempted axial compensation exceeds +/-45 degrees. 4) The attempted action requires a sheet (a motor-driven action). 5) Dumping or parameter plotting was attempted with a tool other than the pen. 6) Distance compensation was attempted on plot data. 7) Adjustment was attempted without a sheet. 8) Pen pressure adjustment was attempted without a sheet. 9) Landing adjustment was attempted without a sheet. 10) Geometric plotting was attempted without a sheet. 11) A new action was attempted when the same action is in operation. (The dump function has been used while the dumping is being executed.)
Remedy: These actions are prohibited and there are no remedies for them. 1) Change to a genuine cable. 2) Perform a loop-back test. If the error persists, replace the main PCM assembly. 3) Connect a cable (genuine cable is recommended). 4) Shut all applications in the host side so that dump data reception from the plotter is the only active application.
Code: 31
Display: ERR 31 NO DATA
Description: Not executable as the receiver buffer is empty
Causes: The receiver buffer stores no data, even tough the “No. COPIES” or “BUFFER DUMP” operation is executed.
Remedy: “No. COPIES” continuously cuts data in the receiver buffer. “BUFFER DUMP” plots or transmits data in the receiver buffer. Therefore, these functions are invalid while the buffer is empty.
Code: 32
Display: ERR 32 DATAtooBIG
Description: Data size exceeds the receiver buffer
Causes: The “No. COPIES” operation has been executed after receiving the data, the size of wich was larger than the capacity of the receiver buffer.
Remedy: 1. If SORTING is set to ON, switch it to OFF and resend data before attempting “No. COPIES” operation. 2. If an error results while SORTING is set to OFF (invalid), this suggests that the data size is not suitable for the “No. COPIES” operation.