Konica-Minolta bizhub C287i
Error Codes List page 1
|
- Code: 10-01, 10-02, 10-40
- Description: Misfeed at manual bypass paper feed section
10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the manual bypass tray starts to feed paper.
10-02 For paper fed from the manual bypass tray, loop forming has not been complete before a sheet enters the registration roller because the rise timing of load to perform registration is earlier than the rise timing of load to form a loop.
10-40 For paper fed from the manual bypass tray, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. - Causes: • Transport motor (M1)
• Registration clutch (CL4)
• Bypass tray paper feed clutch (CL7)
• Registration sensor (PS1)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN13E<A>-9 (ON) 6-C
3 CL4 load check
• Check code: 21
• Multi code: 2
BASEB CN13E<A>-11 (ON) 7-C
4 CL7 load check
• Check code: 20
• Multi code: 3
BASEB CN30E-2 (ON) 13-C
5 M1 load check
• Check code: 40
• Multi code: 1, 3
BASEB CN11E-4 (REM)
BASEB CN11E-7 (LOCK)
3-C
6 BASEB F13E, F21E conduction check - -
7 Replace BASEB.
- Code: 11-01, 11-02, 11-05, 11-40
- Description: Misfeed at tray 1 paper feed section
11-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper.
11-02 For paper fed from the tray 1, due to a delay in paper arrival, loop forming in front of the registration roller is not complete before the rise timing of the transport motor (M1).
11-05 The leading edge of the paper is not turned ON the tray 1 paper feed sensor (PS23) even after the lapse of a given period of time after the tray 1 starts to feed paper.
11-40 For paper fed from the tray 1, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output. - Causes: • Transport motor (M1)
• Tray 1 paper feed clutch (CL3)
• Registration clutch (CL4)
• Registration sensor (PS1)
• Tray 1 paper feed sensor (PS23)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS1 I/O check, sensor check BASEB CN13E<A>-9 (ON) 6-C
3 PS23 I/O check, sensor check BASEB CN5E<A>-3 (ON) 9-C
4 CL3 load check
• Check code: 20
• Multi code: 1
BASEB CN5E<A>-11 (ON) 9-C
5 CL4 load check
• Check code: 21
• Multi code: 2
BASEB CN13E<A>-11 7-C
6 M1 load check
• Check code: 40
• Multi code: 1, 3
BASEB CN11E-4 (REM)
BASEB CN11E-7 (LOCK)
3-C
7 BASEB F13E, F21E conduction check - -
8 Replace BASEB. - -
- Code: 12-01, 12-05, 12-40
- Description: Misfeed at tray 2 paper feed section
12-01 The leading edge of the paper is not turned ON (unblocked) the tray 2 vertical transport sensor (PS19) even after the lapse of a given period of time after the tray 2 starts to feed paper.
12-05 The leading edge of the paper is not turned ON the tray 2 paper feed sensor (PS20) even after the lapse of a given period of time after the tray 2 starts to feed paper.
12-40 For paper fed from the tray 2, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 2 feed section results, if the tray 2 vertical transport sensor (PS19) is turned ON (unblocked) when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 2 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Transport motor (M1)
• Tray 2 paper feed clutch (CL1)
• Tray 2 vertical transport clutch (CL2)
• Tray 2 vertical transport sensor (PS19)
• Tray 2 paper feed sensor (PS20)
• Base board (BASEB) - Remedy: 1 Initial check items - -
2 PS19 I/O check, sensor check BASEB CN5E<B>-16 (ON) 12-C
3 PS20 I/O check, sensor check BASEB CN5E<B>-3 (ON) 10-C
4 CL1 load check
• Check code: 20
• Multi code: 2
BASEB CN5E<B>-11 (ON) 11-C
5 CL2 load check
• Check code: 21
• Multi code: 1
BASEB CN5E<B>-13 (ON) 11-C
6 M1 load check
• Check code: 40
• Multi code: 1, 3
BASEB CN11E-4 (REM)
BASEB CN11E-7 (LOCK)
3-C
7 BASEB F13E, F21E conduction check - -
8 Replace BASEB.
- Code: 13-01, 13-05, 13-40
- Description: Misfeed at tray 3 paper feed section
13-01 The leading edge of the paper is not turned ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper.
13-05 The leading edge of the paper is not turned ON the tray 3 paper feed sensor (PS112) even after the lapse of a given period of time after the tray 3 starts to feed paper.
13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 3 feed section results, if the tray 3 vertical transport sensor (PS113) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 3 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Tray 3 paper feed motor (M111)
• Tray 3 vertical transport motor (M112)
• Tray 3 paper feed sensor (PS112)
• Tray 3 vertical transport sensor (PS113)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS113 I/O check, sensor check PCCB CN4-14 (ON) PC-118/PC-218 5-C
3 PS112 I/O check, sensor check PCCB CN4-11 (ON) PC-118/PC-218 5-C
4 M111 load check
• Check code: 28
• Multi code: 9, 11
PCCB CN5-1 to 8 PC-118/PC-218 4-C
5 M112 load check
• Check code: 28
• Multi code: 17, 19
PCCB CN5-9 to 16 PC-118/PC-218 3 to 4-C
6 Replace PCCB.
- Code: 14-01, 14-05, 14-40
- Description: Misfeed at tray 4 paper feed section
14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper.
14-05 The leading edge of the paper is not turned ON the tray 4 paper feed sensor (PS122) even after the lapse of a given period of time after the tray 4 starts to feed paper.
14-40 For paper fed from the tray 4, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the tray 4 feed section results, if the tray 4 vertical transport sensor (PS123) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the tray 4 feed section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Tray 4 paper feed motor (M121)
• Tray 4 vertical transport motor (M122)
• Tray 4 paper feed sensor (PS122)
• Tray 4 vertical transport sensor (PS123)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS123 I/O check, sensor check PCCB CN18C-5 (ON) PC-218 7-K
3 PS122 I/O check, sensor check PCCB CN18C-2 (ON) PC-218 7-K
4 M121 load check
• Check code: 28
• Multi code: 13, 15
PCCB CN9C-1 to 8 PC-218 6-K
5 M122 load check
• Check code: 28
• Multi code: 21, 23
PCCB CN9C-9 to 16 PC-218 6-K
6 Replace PCCB.
- Code: 16-01, 16-05, 16-40
- Description: Misfeed at LCT feed/vertical transport section
16-01 The leading edge of the paper is not turned ON the LCT vertical transport sensor (PS133) even after the lapse of a given period of time after the LCT starts to feed paper.
16-05 The leading edge of the paper is not turned ON the paper feed sensor (PS132) even after the lapse of a given period of time after the LCT starts to feed paper.
16-40 For paper fed from the LCT, the image write start signal permit continues to be disabled for a predetermined period of time after the timing of the image write start signal output.
- Paper jam of a sheet of paper left at the LCT transport section results, if the LCT vertical transport sensor (PS133) is turned ON when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset.
- Paper jam of a sheet of paper left at the LCT transport section results, if a sheet of paper is determined to exist at a position detected when the main power switch is turned ON, a door is opened and closed, or a misfeed or malfunction is reset. - Causes: • Paper feed motor (M131)
• Vertical transport motor (M132)
• Paper feed sensor (PS132)
• LCT vertical transport sensor (PS133)
• PC control board (PCCB) - Remedy: 1 Initial check items - -
2 PS132 I/O check, sensor check PCCB CN4-11 (ON) PC-418 7-J
3 PS133 I/O check, sensor check PCCB CN4-14 (ON) PC-418 7-J
4 M131 load check
• Check code: 28
• Multi code: 1, 3
PCCB CN5-1 to 8 PC-418 5-J
5 M132 load check
• Check code: 28
• Multi code: 5, 7
PCCB CN5-9 to 16 PC-418 4-J
6 Replace PCCB.