Remedy: Installation of roll paper 1 Is the roll paper correctly installed to the Roll Deck 2? No Install it correctly. Roll 2 Set Sensor (PH9) 2 Check the status of Roll 2 Set Sensor in the Device Status Mode of the Service Mode. Signal Code : 090 (Roll 2 Set Sensor) Is the status “H” when the roll paper is set? No 1. Is there any problem with the Drawer Connector which connects the machine and the Roll Deck. 2. Check if there is any problem with the wire connected to the Roll 2 Set Sensor. 3. Replace the Roll 2 Set Sensor if there is no problem with the wire. Roll 2 Feed Clutch (CL6) 3 Check the operation of Roll 2 Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 08 (Roll 2 Feed Clutch) Does the clutch operate when you change the output signal from “L” to “H”? No 1. Check if there is any problem with the wire connected to the Roll 2 Feed Clutch. 2. Replace the Roll 2 Feed Clutch if there is no problem with the wire. Main Motor (M1) 4 Check the status of Roll 2 Set Sensor in the Device Status Mode of the Service Mode while making the following operation. (Signal Code : 090) 1. Set the leading edge of roll 2 between feeding rollers. (Leading edge must not pass over the Roll 2 Set Sensor.) 2. Close the Roll Deck. Does the status change from “L” to “H” when the machine is transporting the paper? No 1. Check the driving belts of the Roll Deck. 2. Check if there is any problem with the wire connected to the Main Motor. 3. Replace the Main Motor if there is no problem with the wire. Yes 1. Remove the whole Roll Deck, and then re-install it to the machine correctly.
Code: J-0102
Description: Roll 1 Feeding Jam “Delay”
Causes:
Remedy: Installation of roll paper 1 Is the roll paper correctly installed to the Roll Deck 2? No Install it correctly. Roll 1 Set Sensor (PH7) 2 Check the status of Roll 1 Set Sensor in the Device Status Mode of the Service Mode. Signal Code : 089 (Roll 1 Set Sensor) Is the status “H” when the roll paper is set? No 1. Is there any problem with the Drawer Connector which connects the machine and the Roll Deck. 2. Check if there is any problem with the wire connected to the Roll 1 Set Sensor. 3. Replace the Roll 1 Set Sensor if there is no problem with the wire. Roll 1 Feed Clutch (CL4) 3 Check the operation of Roll 1 Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 06 (Roll 1 Feed Clutch) Does the clutch operate when you change the output signal from “L” to “H”? No 1. Check if there is any problem with the wire connected to the Roll 1 Feed Clutch. 2. Replace the Roll 1 Feed Clutch if there is no problem with the wire. Main Motor (M1) 4 Check the status of Roll 1 Set Sensor in the Device Status Mode of the Service Mode while making the following operation. (Signal Code : 089) 1. Set the leading edge of roll 1 between feeding rollers. (Leading edge must not pass over the Roll 1 Set Sensor.) 2. Close the Roll Deck. Does the status change from “L” to “H” when the machine is transporting the paper? No 1. Check the driving belts of the Roll Deck. 2. Check if there is any problem with the wire connected to the Main Motor. 3. Replace the Main Motor if there is no problem with the wire. Yes 1. Remove the whole Roll Deck, and then re-install it to the machine correctly.
Code: J-0103
Description: Feeding Jam “Delay” (J-0103) & “Early” (L-0303)
Causes:
Remedy: Mis-feed of paper 1 Does the paper mis-fed occur between Roll 1 Set Sensor and Feed Sensor? Yes Remove the mis-fed paper. Feed Sensor (PH6) 2 Check the status of Feed Sensor in the Device Status Mode of the Service Mode. Signal Code : 092 (Feed Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Is there any problem with the Drawer Connector which connects the machine and the Roll Deck. 2. Check if there is any problem with the wire connected to the Feed Sensor. 3. Replace the Feed Sensor if there is no problem with the wire. Cutter Home Position Sensor (MS6 & MS7) 3 Check the status of Cutter Home Position Sensors in the Device Status Mode of the Service Mode. Signal Code 078 (Cutter Home Position Sensor Right) 079 (Cutter Home Position Sensor Left) Is the status “H” when the Cutter is at each home position? And is it “L” when the Cutter is not at the home position? No 1. Check if there is any problem with the wire connected to the Cutter Home Position Sensor. 2. Replace the Cutter Home Position Sensors if there is no problem with the wire. Driving mechanism 4 Check the operation of Feed Clutch in the Device Operation Mode of the Service Mode. Signal Code : 10 (Feed Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Feed Clutch and Main Motor operate correctly? No Replace the Feed Clutch or Main Motor if it is defective.
Code: J-0104, J-0204, J-0304
Description: Reg. Jam “Delay” (J-0104), “Stay” (J-0204) & “Early” (J-0304)
Causes:
Remedy: Mis-feed of paper 1 Does the paper mis-fed occur around the Registration Roller? Yes Remove the mis-fed paper. Registration Sensor (PH1) 2 Check the status of Registration Sensor in the Device Status Mode of the Service Mode. Signal Code : 084 (Registration Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Registration Sensor. 2. Replace the Registration Sensor if there is no problem with the wire. Engine Unit 3 Is the Engine Unit closed firmly until it is locked? (Is the pressure around the Registration Roller correct?) No 1. Close the Engine Unit firmly. 2. Adjust the pressure around the Registration Roller. Driving mechanism 4 Check the operation of Registration Clutch in the Device Operation Mode of the Service Mode. Signal Code : 11 (Registration Clutch) Also open and close the Roll Deck, and check if the Main Motor rotates correctly. Does each Registration Clutch and Main Motor operate correctly? No Replace the Registration Clutch or Main Motor if it is defective.
Code: J-0106, J-0206, J-0306
Description: Internal Jam “Delay” (J-0106), “Stay” (J-0206) & “Early” (J-0306)
Causes:
Remedy: Mis-feed of paper 1 Does the paper mis-fed occur around the separation area? Yes Remove the mis-fed paper. Separation Sensor (PH2) 2 Check the status of Separation Sensor in the Device Status Mode of the Service Mode. Signal Code : 010 (Separation Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Separation Sensor. 2. Replace the Separation Sensor if there is no problem with the wire. Transfer / Separation Corona 3 Is the Transfer / Separation Corona Unit installed to the machine correctly? Yes Install the Transfer / Separation Corona Unit correctly. Is the Corona Wire broken? Yes Replace the Corona Wire. HV Power Supply 4 Is the output from the HV Power Supply to the Separation Corona correct? No Replace the HV Power Supply.
Code: J-0107, J-0207, J-0307
Description: Fuser Jam “Delay” (J-0107), “Stay” (J-0207) & “Early” (J-0307)
Causes:
Remedy: Mis-feed of paper 1 Does the paper mis-fed occur around the fuser area? Yes Remove the mis-fed paper. Exit Sensor (PH3) 2 Check the status of Exit Sensor in the Device Status Mode of the Service Mode. Signal Code : 011 (Exit Sensor) Is the status “L” when the paper is not passing beside the sensor? And is it “H” when the paper is passing beside the sensor? No 1. Check if there is any problem with the wire connected to the Exit Sensor. 2. Replace the Exit Sensor if there is no problem with the wire.