Display: Paper is jammed in the printer. Turn off the printer, open the scanner unit, and remove the paper. See your documentation.
Description: Paper jam error
Causes: Paper stays in the paper path after paper ejection.
Remedy: 1. Check if the ASF Unit is properly installed. 1. Install the ASF Unit properly. 2. Check if the Paper Back Lever operates correctly in the paper loading sequence. 2. Set the Extension Spring 6.45 between the ASF Frame and the Paper Back Lever. 1. Check if the Extension Spring Retard operates correctly in the paper loading sequence. 1. Set the Extension Spring Retard between the Retard Roller Unit and the ASF Frame. 1. Check if the Star Wheel Holder Assy is correctly assembled. 1. Reassemble the Star Wheel Holder Assy correctly. 2. Check if the Star Wheel Holders does not come off. 2. Reassemble the Star Wheel Holders correctly. 1. Check if the EJ Roller Unit is correctly assembled. 1. Reassemble the EJ Roller Unit correctly. 2. Check if the Spur Gear 51.5 is not damaged. 2. Replace the EJ Roller Unit with a new one. 1. Check if the Upper Paper Guide Unit is correctly assembled. 1. Reassemble the Upper Paper Guide Unit to the Main Frame correctly.
Code: 06
Display: You need to replace the following ink cartridge(s).
Description: Ink end error
Causes: Ink is out in some I/C.
Remedy: 1. Check if Ink Cartridge is properly installed. 1. Install the Ink Cartridge properly. 2. Check if the Memory Chip is not disconnected or not chipped. 1. Check if the Head FFC is connected to connector on the CSIC Board. 1. Connect the Head FFC to connector on the CSIC Board. 2. Check if the CSIC Board is not damaged. 2. Replace the CSIC Board with a new one. 3. Check if the CSIC Connector is not damaged. 1. Replace the CSIC Board with a new one.
Code: 07
Display: The following ink cartridges have not been installed. Install them.
Description: No ink cartridge error
Causes: No I/C is set.
Remedy: 1. Check if Ink Cartridge is properly installed. 1. Install the Ink Cartridge properly. 2. Check if the Memory Chip is not disconnected or not chipped. 1. Check if the Head FFC is connected to connector on the CSIC Board. 1. Connect the Head FFC to connector on the CSIC Board. 2. Check if the CSIC Board is not damaged. 2. Replace the CSIC Board with a new one. 3. Check if the CSIC Connector is not damaged. 1. Replace the CSIC Board with a new one.
Code: 08
Display: Cannot recognize the following ink cartridge(s). Install them correctly.
Description: Incorrect ink cartridge
Causes: Incorrect I/C is set.
Remedy: 1. Check if Ink Cartridge is properly installed. 1. Install the Ink Cartridge properly. 2. Check if the Memory Chip is not disconnected or not chipped. 1. Check if the Head FFC is connected to connector on the CSIC Board. 1. Connect the Head FFC to connector on the CSIC Board. 2. Check if the CSIC Board is not damaged. 2. Replace the CSIC Board with a new one. 3. Check if the CSIC Connector is not damaged. 1. Replace the CSIC Board with a new one.
Code: 09
Display: The ink cartridge cover is open. Open the scanner unit and close the ink cartridge cover. Press OK to continue.
Description: Ink cartridge cover open error
Causes: Ink replacement was attempted with the Ink Cartridge Cover open.
Remedy: 1. Close the Ink Cartridge Cover.
Code: 10
Display: Paper out. Load paper and press the Start button.
Description: Paper out error
Causes: Failure to load paper to print.
Remedy: 1. Check if any paper dust is not adhered to the surface of the LD Roller. 1. Set a cleaning sheet in the ASF Unit up side down. Then holding the top edge, try to load the paper from the Printer driver. The micro pearl on the LD Roller surface is removed. To remove severe smear, staple a cloth moistened with alcohol to a post card and clean the roller in the same manner. 1. Check if the Hopper operates correctly in the paper loading sequence. 1. Reassemble the Compression Spring 1.94 between the Base Frame and the Hopper.