Sharp MXM2630
Simulation mode. List of classic mode 50 - 67
| Sim No. | Function | Easy Mode | |||
| Installation | Maintenance | Adjustment and Settings |
|||
| 50 | 5 | Adjust the printer image position and the image loss | 1-1 | ||
| 6 | Adjust SPF image position and the image loss | 1-1 | |||
| 10 | Adjust the image position in the each paper feed tray | 1-2 | 2-1 | 1-1 | |
| 12 | Adjust the scan image off center position | 1-1 | |||
| 27 | Adjust the scan image loss in the FAX and image send mode | ||||
| 28 | Adjust the image loss, void area, image off center and image magnification ratio | ||||
| 51 | 1 | Set the transfer voltage timing | |||
| 2 | Adjust the contact pressure on paper by the main unit and the SPF resist roller | ||||
| 53 | 6 | Adjust the detection level of the SPF document width | 3 | ||
| 7 | Adjust the SPF document width sensor | ||||
| 8 | Adjust the document lead edge and the scan position | 3 | |||
| 9 | Set the dirt detection and scan position | ||||
| 10 | Execute SPF dirt detection | ||||
| 55 | 1 | Set the specification of the engine operation | |||
| 2 | Set the specification of the scanner operation | ||||
| 3 | Set the specification of the controller operation | ||||
| 10 | Used to set the special stamp text for Taiwan | ||||
| 56 | 1 | Transport data between EEPROM and STORAGE | |||
| 2 | Backup the data in the EEPROM and STORAGE to the USB memory | ||||
| 3 | Backup the document filing data to the USB memory | ||||
| 4 | Backup the job log data to the USB memory | ||||
| 5 | Backup the SIM22-6 data in the text format to the USB memory | ||||
| 6 | Backup the SIM23-2 data in the text format to the USB memory | ||||
| 7 | Backup the syslog data to the USB memory | ||||
| 15 | Restore the data to MFP EEPROM | ||||
| 20 | Set the option HDD | 2-1 | |||
| 21 | Cancel the option HDD setting | 2-1 | |||
| 99 | Backup all log data to the USB memory | 3-4 | 1-5 | 9-4 | |
| 60 | 1 | Check read/write memory operation | |||
| 61 | 1 | Check the LSU polygon motor rotation and laser detection | |||
| 3 | Set the laser power | ||||
| 11 | Adjust laser power auto correction | 2-3 | 1-2 1-3 |
||
| 12 | Adjust laser power manual correction | ||||
| 13 | Clear laser power correction data | 2-3 | 1-3 | ||
| 14 | Set the laser power correction | 1-3 | |||
| 62 | 1 | Execute hard disk format | |||
| 2 | Check read/write hard disk operation (partial) | ||||
| 3 | Check read/write hard disk operation (all areas) | ||||
| 6 | Execute hard disk self diagnostics | ||||
| 7 | Print hard disk self diagnostics error log | ||||
| 8 | Execute hard disk format (except system area) | ||||
| 10 | Clear the job completion data | ||||
| 11 | Delete the document filing data | ||||
| 62 | 12 | Set auto format in hard disk trouble | |||
| 13 | Execute hard disk format (preinstalled data area) | ||||
| 14 | Clear database file | ||||
| 63 | 1 | Check shading correction data | |||
| 2 | Execute shading correction | 1-5 | 3 | ||
| 3 | Adjust scanner (CCD) color balance and gamma correction | 1-5 | 2-3 | 3 | |
| 4 | Check the scanner test chart patch density | ||||
| 5 | Reset the scanner (CCD) color balance and gamma correction | 2-3 | 3 | ||
| 11 | Set gray balance target in the copy mode | 5 | |||
| 64 | 2 | Test print | 8 | ||
| 4 | Printer test print | ||||
| 5 | Printer test print (PCL) | 1-4 | |||
| 6 | Printer test print (PS) | ||||
| 65 | 1 | Adjust the touch panel detection coordinate | 7 | ||
| 2 | Check the touch panel detection coordinate | ||||
| 5 | Check the operation panel key input | ||||
| 66 | 1 | Set the specification of image send operation | 2-3 | ||
| 2 | Set country code | ||||
| 3 | Check FAX PWB memory | ||||
| 4 | Check signal output level (max) | ||||
| 5 | Check signal output level (soft SW) | ||||
| 6 | Used to print the confidential registration check table | ||||
| 7 | Used to output all image data saved in the image memory | ||||
| 8 | Used to send the selected sound message to the line and the speaker (max) | ||||
| 9 | Used to send the selected sound message to the line and the speaker (soft SW) | ||||
| 10 | Used to clear the FAX and image send image data | ||||
| 11 | Used to send the selected signal at 300bps to the line and the speaker (max) | ||||
| 12 | Used to send the selected signal at 300bps to the line and the speaker (soft SW) | ||||
| 13 | Used to register dial number for Sim66- 14/15/16 dial test | ||||
| 14 | Used to excute the dial pulse (10pps) send test and to adjust the make time | ||||
| 15 | Used to excute the dial pulse (20pps) send test and to adjust the make time | ||||
| 16 | Used to execute the DTMF signal send test and to adjust the send level | ||||
| 17 | Used to send the DTMF signal to the line and the speaker (max) | ||||
| 18 | Used to send the DTMF signal to the line and the speaker (soft SW) | ||||
| 21 | Used to print the selected iyems (system error, protocol monitor) | ||||
| 22 | Used to set the handset sound volume | ||||
| 29 | Used to intialize the telephone book data | ||||
| 30 | Used to display the TEL/LIU status change, the display is highlighted by status change | ||||
| 31 | Used to set ON/OFF the port for output to TEL/LIU | ||||
| 32 | Used to check the fixed data received from the line and to display the result | ||||
| 66 | 33 | Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected the display is highlighted | |||
| 36 | Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the command line individually |
||||
| 39 | Used to check and change the destination setting saved in EEPROM of the FAX | ||||
| 42 | Used to rewrite the program to power control installed in the FAX | ||||
| 43 | Used to write the adjustment value into the power control installed in the FAX | ||||
| 61 | Set the specification of image send operation | ||||
| 62 | Backup FAX received data to the USB memory | ||||
| 67 | 17 | Reset printer memory | |||
| 24 | Adjust printer gray balance (auto) | 6 | |||
| 25 | Adjust printer gray balance (manual) | 1-4 | 6 | ||
| 26 | Set gray balance target in the printer mode | 6 | |||
| 31 | Clear printer calibration data | ||||
| 33 | Adjust printer screen gamma | ||||
| 34 | Set the density correction of printer high density area | ||||
| 36 | Adjust the density in the printer low density area | ||||
| 46 | Adjust printer image edge | ||||
| 52 | Set gamma default value of the printer screen |
1-3 | |||
| 54 | Adjust printer gray balance | 1-3 | |||