Sharp MXM160D
Simulation mode. List of simulation codes 25 - 67
Main code | Sub code | Contents |
---|---|---|
25 | 02 | Toner density reference control level setting (automatic development adjustment) |
10 | Polygon motor operation check | |
26 | 01 | Job separator setting |
02 | Size setting | |
03 | Auditor setting | |
04 | Copier duplex setting | |
05 | Count mode setting | |
06 | Destination setting | |
07 | Machine condition check | |
18 | Toner save mode setting | |
20 | Job separator paper exit mode setting | |
22 | Language setting clear | |
30 | CE mark conformity control ON/OFF | |
31 | Auditor mode exclusive setup | |
36 | Cancel of stop at maintenance life over | |
37 | Cancel of stop at developer life over | |
38 | Cancel of stop at drum life over | |
39 | Memory capacity check | |
42 | Transfer ON/OFF timing control setting | |
43 | Side void amount setting | |
51 | Copy temporary stop function setting | |
54 | LCD contrast PWM duty setting | |
56 | Life correction ON/OFF setting | |
60 | [FAX] key Enable/Disable setting | |
73 | Toner save setting display/non-display | |
74 | Total counter display change setting | |
30 | 01 | Paper sensor status display |
41 | 01 | Document size detection photo sensor check |
02 | Document size detection photo sensor detection level adjustment | |
03 | Document size detection photo sensor light receiving/ detection level check | |
04 | Detection level adjustment when the document size is settled(15degrees - 20degrees) | |
42 | 01 | Developing counter clear |
43 | 01 | Fusing temperature setting (Normal copy) |
12 | Standby mode fusing fan rotation setting | |
13 | Paper interval control allow/inhibit setting | |
44 | 01 | Enable/Disable setting of toner density control correction |
16 | Toner density control data check and toner density correction quantity display | |
34 | Transfer current setting | |
46 | 01 | Copy density adjustment (300dpi) |
02 | Copy density adjustment (600dpi) | |
09 | Copy exposure level adjustment, individual setting (Text) 300dpi | |
10 | Copy exposure level adjustment, individual setting (Text) 600dpi | |
11 | Copy exposure level adjustment, individual setting (Photo) 600dpi | |
18 | Image contrast adjustment (300dpi) | |
19 | Exposure mode setting (Gamma table setting/AE operation mode setting/ Photo image process setting) |
|
20 | SPF/RSPF exposure correction *2 | |
29 | Image contrast adjustment (600dpi) | |
30 | AE limit setting | |
46 | 31 | Image sharpness adjustment |
48 | 01 | Main/sub scanning magnification ratio adjustment |
05 | SPF/RSPF mode sub scanning magnification ratio adjustment in copying *2 | |
49 | 01 | Flash ROM program writing mode |
50 | 01 | Image lead edge adjustment |
06 | Copy lead edge position adjustment (SPF/RSPF) *2 | |
10 | Paper off-center adjustment | |
12 | Document off-center adjustment | |
18 | Memory reverse position adjustment in duplex copy *1 | |
19 | Rear edge void adjustment in duplex copy *6 | |
51 | 02 | Resist amount adjustment |
53 | 08 | SPF/RSPF scanning position automatic adjustment *2 |
10 | SPF/RSPF scanning position setting | |
61 | 02 | Laser power correction ON/OFF |
03 | HSYNC output check | |
63 | 01 | Shading check |
07 | SPF/RSPF automatic correction *2 | |
64 | 01 | Self print |
65 | 10 | Key reception time setting display/non-display setting |
11 | Info lamp setting | |
67 | 50 | USB reception speed adjustment |
<Execution inhibit conditions>
*1)Execution is inhibited when the duplex setup is OFF and other than RSPF is set.
*2)Execution is inhibited when OC.
*3)Execution is inhibited when SPF. (Not RSPF)
*4)Execution is inhibited when the job separator is not installed.
*5)Execution is inhibited when the model is not provided with the CRUM.
*6)Execution is inhibited when the duplex setup is OFF.