Sharp MXC305W
Simulation mode. List of classic mode. Codes 7-12 - 27-7
Sim No. | Content | Installation | Maintenance | Adjustment and Settings |
---|---|---|---|---|
7-12 | The document reading number of sheets (for aging operation) | |||
8-1 | Used to check and adjust the operations of the developping voltage in each print mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | |||
8-2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | |||
8-6 | Used to check and adjust the operation of the transport voltage and the control circuit | |||
10-1 | Used to check the operations of the toner supply mechanism (toner supply clutch) and the related circuit | |||
13 | Used to cancel U1 trouble | 5 | 6 | |
14 | Used to cancel H3, H4, H5 troubles | 5 | 6 | |
16 | Used to cancel the self-diag U2 trouble | 5 | 6 | |
21-1 | Used to set the maintenance cycle | 4 | ||
22-1 | Used to check the print count value in each section and each operation mode | 3-1 | 1-1 | 9-1 |
22-2 | Used to check the total number of misfeed and troubles |
|||
22-3 | Used to check misfeed positions and the misfeed count of each position | 1-2 | ||
22-4 | Used to check the trouble (self diag) history | |||
22-5 | Used to check the ROM version of each unit | 3-2 | 1-3 | 9-2 |
22-6 | Used to output the setting/adjustment data, the firmware version and the counter list | 3-3 | 1-4 | 9-3 |
22-8 | Used to check the number of operations (counter value) of the SPF and the scan (reading) unit | 1-1 | ||
22-9 | Used to check the number of use (print quantity) of each paper feed section | 3-1 | 1-1 | 9-1 |
22-10 | Used to check the system configuration (option, internal hardware) | 3-2 | 1-3 | 9-2 |
22-11 | Used to check the use frequency (send/ receive) of FAX | |||
22-12 | Used to check the SPF misfeed positions and the number os misfeed at each position | 1-2 | ||
22-13 | Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the fusing unit) | 3-1 | 1-1 | 9-1 |
22-14 | Used to display the use status of the toner cartridge | |||
22-18 | Used to display the user data delete history | |||
22-19 | Used to check the values of the counters related to the scan - image send | |||
22-40 | Used to display the error code list and the contents | |||
22-41 | Used to check JAM code information | |||
22-42 | Used to check the JAM/trouble data | |||
22-43 | JAM data details display | |||
22-90 | Used to output the various set data lists | |||
23-2 | Used to output the trouble history list of paper jam and misfeed | 3-3 | 1-4 | 9-3 |
23-80 | Used to check the operation of paper feed and paper transport in the paper feed section and the paper transport section. Used to output the list of the operation status of the sensor and detectors in the paper feed section and the paper transport section |
|||
23-81 | Used to export paper feed time list | |||
24-1 | Used to clear the jam counter and the trouble counter | 3 | ||
24-2 | Used to clear the number of use (the number of prints) of each paper feed section | 3 | ||
24-3 | Used to clear the SPF and the scan (reading) unit counter | 3 | ||
24-4 | Used to clear the maintenance counter the printer counter of the transport unit and the fusing unit | 3 | ||
24-5 | Used to clear the developer counter and toner remaining counter | |||
24-35 | Used to clear the toner cartridge use status data | |||
25-1 | Used to check the operations of the developing section | |||
25-2 | Used to make the initial setting of toner density when replacing developer | 2-2 -5 |
2 | |
25-4 | Used to display the operation data of the toner supply quantity | |||
25-5 | Used to display the toner density correction data | |||
25-10 | Developer/drum serial no setting | |||
26-2 | Used to set the paper size of the large capacity tray (LCC) | 2-1 | ||
26-3 | Used to set the specifications of the auditor | 2-1 | ||
26-6 | Used to set the specifications of the destination | |||
26-7 | Used to set the machine ID | |||
26-10 | Used to set the trial mode of the network scanner |
|||
26-18 | Used to set Disable/Enable of the toner save mode operation | 2-4 | ||
26-30 | Used to set the operation mode corresponding to the CE mark | |||
26-32 | Used to set the specifications of the fusing cleaning operation | |||
26-33 | Special function setting | 2-1 | ||
26-35 | Used to set the display/mode of Sim 22-4 trouble history when a same trouble occurred repeatedly. There are two display modes. Display as one trouble and display as several series of troubles | |||
26-38 | Used to set continue/stop of print when the maintenance life is reached | |||
26-41 | Used to set Enable/Disable of the magnification ratio automatic select function in the center binding mode | |||
26-49 | Used to set the print speed of postcard mode | |||
26-50 | Used to set functions | 2-1 | ||
26-52 | Used to set whether non-printed paper is counted up or not | 2-2 | ||
26-66 | Simulation password setting | |||
26-69 | Used to set the operating conditions for toner near end | 2-4 | ||
26-73 | Enlargement continuous shoot, A3 wide copy mode image loss adjustment | |||
26-74 | Used to set the OSA trial mode | |||
26-78 | Used to set the password of the remote operation panel | 2-1 | ||
26-79 | Used to set Yes/No of the pop-up display of security | |||
26-85 | Simulation function setting | |||
27-2 | Used to set the sender's registration number and the HOST server telephone number | 2-5 | ||
27-4 | Used to set the initial call and toner order auto send |
2-5 | ||
27-5 | Used to set the machine tag No. | |||
27-6 | Used to set of the manual service call | |||
27-7 | Used to set of the enable, alert callout | 2-5 |