Sharp MX5151
Simulation mode. List of Classic mode. Codes 50 - 66
Main | Sub | Functions | Section |
---|---|---|---|
50 | 22 | Used to adjust the image registration. (Main scan direction, sub scan direction) (Auto adjustment)/OPC drum phase adjustment (Auto adjustment) | |
23 | Used to set the temperature correction. | ||
24 | Used to display the detail data of SIM 44-2, 50-20 and 22. | ||
27 | Used to perform the image loss adjustment of scanned images in the FAX or image send mode. | ||
51 | 1 | Used to adjust the ON/OFF timing of the secondary transport voltage. | |
2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the DSPF registration roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) |
||
53 | 6 | Used to adjust the detection level of the DSPF document width. | |
7 | Used to adjust the DSPF document size width sensor. | ||
8 | Used to adjust the document lead edge reference and the DSPF mode document scan position. | ||
9 | DSPF dirt detection setting. | ||
10 | DSPF dirt detection execution. | ||
12 | Check the operation of the SPF double feed detection sensor | ||
55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
2 | Used to set the specifications of the scanner control operation. (SOFT SW) | ||
3 | Used to set the specifications of the controller operation. (SOFT SW) | ||
10 | Used to set the special stamp text. (Taiwan only) | ||
56 | 1 | Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) | |
2 | Used to backup the data in the EEPROM and HDD (including user authentication data and address data) to the USB memory. (Corresponding to the device cloning and the storage backup.) | ||
3 | Used to backup the document filing data to the USB memory. | ||
4 | Used to backup the JOB log data to the USB memory. | ||
5 | Used to import the SIM22-6 data to a USB memory in the TEXT format. | ||
6 | Used to output the JAM/trouble data. | ||
7 | Used to export system log data. | ||
8 | Used to perform ICC profile update. | ||
15 | Used to restore MFP EEPROM data. | ||
56 | Used to set the adjustment value | ||
99 | Used to export system log data. | ||
60 | 1 | Used to check the memory operations (read/write) of the MFP PWB. | |
61 | 1 | Used to check the LSU polygon motor rotation and laser detection. | LSU |
2 | Used to set the laser power (FIERY) | ||
3 | Used to set the laser power | ||
4 | Used to print the print image skew adjustment pattern. (LSU unit) | ||
11 | Used to correct the laser power automatically. | ||
12 | Laser power manual correction | LSU | |
13 | Used to clear the laser power correction value. | ||
14 | Used to set the laser power correction. | ||
62 | 1 | Used to format the storage | |
3 | Used to check read/write of the hard disk (all areas). | ||
4 | Storage check/format (Logical) | ||
7 | Used to print the hard disk self diagnostics error log. | ||
9 | Storage data clear | ||
12 | Used to set Enable/Disable of auto format in a hard disk trouble. | ||
14 | Used to delete the document filing management data. | HDD | |
21 | Storage information display | ||
63 | 1 | Used to display the shading correction result. | Scanner |
2 | Used to perform shading. | ||
3 | Used to perform scanner (CCD) color balance and gamma auto adjustment. | Scanner | |
4 | Used to display the SIT chart patch density. | ||
5 | Used to perform the scanner (CCD) color balance and gamma default setting. | ||
7 | Used to register the service target of the copy mode auto color balance adjustment. | ||
8 | Used to set the default of the service target of the copy mode auto color balance adjustment. | ||
11 | Used to set the target color balance of the copy mode auto color balance adjustment. | ||
64 | 1 | Test print. (Self print) (Color mode) | |
2 | Test print. (Self print) (Monochrome mode) | ||
4 | Printer test print. (Self print) | ||
5 | Printer test print. (Self print) (PCL) | ||
6 | Printer test print. (Self print) (PS) | ||
65 | 1 | Used to adjust the touch panel (LCD display section) detection coordinates. | Operation panel section |
2 | Used to display the touch panel (LCD display section) detection coordinates. | ||
5 | Used to check the operation panel key input. | ||
66 | 1 | Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking with the LCD. | FAX |
2 | Used to enter a country code and set the default value for the country code. | FAX | |
3 | Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the result. | FAX | |
4 | Used to send the selected signals to the line and the main unit speaker. (Send level: max.) | FAX | |
5 | Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting) (For the kinds of send signals, refer to SIM66-04.) |
FAX |