Xerox WorkCentre 3345

Bill
Posts: 64
Joined: Sat Oct 21, 2017 9:50 pm

Xerox WorkCentre 3345

Postby Bill » Tue Nov 02, 2021 6:23 pm

Xerox WorkCentre 3335, 3345
ADF/DADF Jam
Applicable Errors
• 05-100: DADF Jam1
• 05-300: DADF Jam3
• 05-400: DADF Jam4
• 05-700: DADF Jam7
• 05-900: DADF Jam0
Initial Actions
• Open the ADF/DADF Cover and remove all originals from the document feeder.
• Turn the machine off and then on, if the error persists use the following procedure.
Applicable Parts
• DADF Pick Up Unit (PL 8.1A .16, Parts List 8.1A WorkCentre 3345 DADF)
• ADF Pick Up Assembly (PL 7.1.9 and PL .7.1.10, Parts List 7.1 WorkCentre 3335 SCANNER and ADF)
• ADF Paper Path Assembly, (ADF Paper Path Assembly (WorkCentre 3335))
• DADF Feed Roller (PL 8.2.14, Parts List 8.2 WorkCentre 3345 Lower DADF)
• DADF Rubber Unit (PL 8.2.14, Parts List 8.2 WorkCentre 3345 Lower DADF)
• DADF Lifting Solenoid (PL 8.18, Parts List 8.1 WorkCentre 3345 SCANNER and DADF).
• DADF Feed Sensor (PL 8.2.24, Parts List 8.2 WorkCentre 3345 Lower DADF)
• DADF Registration Sensor (PL 8.2.13, Parts List 8.2 WorkCentre 3345 Lower DADF)
• DADF Drive (PL 8.5.8, Parts List 8.5 WorkCentre 3345 Drive DADF)
• ADF Motor (PL 7.1A.16, Parts List 7.1A WorkCentre 3335 ADF)
• DADF Assembly (PL 8.1A.1, Parts List 8.1A WorkCentre 3345 DADF)
• ADF Assembly (PL 7.1A.1, Parts List 7.1A WorkCentre 3335 ADF)

Procedure
  1. Is the ADF/DADF Cover completely closed? Does the error persist?
    Y: Go to step 3.
    N: Close the ADF/DADF Cover and go to step 2.
  2. Does the error persist?
    Y: Go to step 3.
    N: Complete.
  3. Check the connectors and wiring between the ADF/DADF and the main board.
    WorkCentre 3335: CN36
    WorkCentre 3345:
    • CN12 (main board) to CN1 (RADF joint PBA)
    • CN2 (RADF joint PBA) to CN2 (DADF)
    • CN3 (RADF joint PBA) to CN1 (DADF)
    Repair the wiring as necessary.
    Y: Go to step 4.
    N: Complete.
  4. Does the ADF/DADF pick the original from the input tray?
    Y: Go to step 5.
    N: Go to step 8.
  5. Check the media path.
    Is there debris in the media path? (clean only with a dry, lint-free cloth)
    Y: Remove the debris and go to Step 6.
    N: Go to step 8.
  6. Enter dC330 Component Control, code 05-200.
    Does the DADF Scan Motor rotate?
    Y: Go to step 7.
    N: Install a new DADF drive (PL 8.5.8, Parts List 8.5 WorkCentre 3345 Drive DADF)
  7. Does the error persist?
    Y: Go to step 8.
    N: Complete.
  8. • WorkCentre 3345: Use a dry lint free cloth to clean the DADF Feed Roller (PL 8.2.14, Parts List 8.2 WorkCentre 3345
    Lower DADF)
    • WorkCentre 3335: Use a dry lint free cloth to clean the ADF Pick Up Assembly rollers (PL 7.1.9 and PL 7.1.10, Parts List 7.1 WorkCentre 3335 SCANNER and ADF ).
    Rotate the rollers by hand.
    Do the rollers rotate smoothly?
    Y: Go to step 9.
    N: • WorkCentre 3345: Install a new DADF Feed Roller (PL 8.2.14, Parts List 8.2 WorkCentre 3345 Lower DADF)
    • WorkCentre 3335: ADF Pick Up Assembly (PL 7.1.9 and PL 7.1.10, Parts List 7.1 WorkCentre 3335 SCANNER and ADF)
  9. Does the error persist?
    Y: Go to step 10.
    N: Complete.
  10. • WorkCentre 3345, install a new DADF Pick Up Unit (PL 8.1.16, Parts List 8.1 WorkCentre 3345 SCANNER and DADF).
    • WorkCentre 3335, install a new ADF Paper Path Assembly (ADF Paper Path Assembly (WorkCentre 3335)).
    Does the error persist?
    Y: • WorkCentre 3345, go to step 11.
    • WorkCentre 3335, go to step 14.
    N: Complete.
  11. Install a new DADF Lifting Solenoid (PL 8.18, Parts List 8.1 WorkCentre 3345 SCANNER and DADF).
    Does the error persist?
    Y: Install a new DADF Separator Pad (DADF Separator Pad). Go to step 12.
    N: Complete.
  12. Enter dC330 Component Control, code 05-130 DADF Registration Sensor.
    • If the Sensor changes state (is good), go to step 13.
    • If the Sensor does not change state (is bad), install a new DADF Registration Sensor (PL 8.2.13, Parts List 8.2 WorkCentre 3345 Lower DADF).
    Y: • If the Sensor changes state (is good), replace the DADF PWB Section 4 (PL 8.1A .13, Parts List 8.1A WorkCentre 3345 DADF).
    • If the error continues, replace the Main Board Section (PL 6.1. 7, Parts List 6.1 WorkCentre 3335/3345 Main).
    N: • If the Sensor does not change state (is bad), replace the DADF Feed/Registration Sensor (PL 8.2.13, Parts List 8.2 WorkCentre 3345 Lower DADF).
    • If the error continues, replace the DADF (PL 8.1A.13, Parts List 8.1A WorkCentre 3345 DADF) and then the Main Board (PL 6.1.7, Parts List 6.1 WorkCentre 3335/3345 Main).
  13. Enter dC330 Component Control, code 05-100 DADF Feed Sensor.
    • If the Sensor changes state (is good), replace the DADF Board (PL 8.1A.13, Parts List 8.1A WorkCentre 3345 DADF).
    • If the Sensor does not change state (is bad), install a new DADF Feed Sensor (PL 8.2.24, Parts List 8.2 WorkCentre 3345 Lower DADF).
    Enter dC330 Component Control, code 05-130 DADF Registration Sensor. If the Sensor does not change state (is bad),
    install a new DADF Registration Sensor (PL 8.2.13, Parts List 8.2 WorkCentre 3345 Lower DADF).
    Does the error persist?
    Y: Go to step14.
    N: Complete.
  14. Install a new DADF Board (PL 8.1A .13, Parts List 8.1A WorkCentre 3345 DADF.)
    Does the error persist?
    Y: Install a new DADF Drive Unit (PL 8.5.8, Parts List 8.5 WorkCentre 3345 Drive DADF)
    N: Complete.
  15. Does the error persist?
    Y: WorkCentre 3345: Install a new DADF (PL 8.1.1, Parts List 8.1 WorkCentre 3345 SCANNER and DADF).
    WorkCentre 3335: Install a new ADF (PL 7.1.1, Parts List 7.1 WorkCentre 3335 SCANNER and ADF).
    N: Complete.

Return to “Xerox WorkCentre”

Who is online

Users browsing this forum: No registered users and 2 guests