Riso ComColor FW5230

Alvin
Posts: 60
Joined: Mon Feb 01, 2021 12:31 pm

Riso ComColor FW5230

Postby Alvin » Tue Nov 09, 2021 12:00 pm

Riso ComColor FW5230, FW6231, FW5000, FW1230
How to enter a test mode
Press and hold the [*], [8] and [#] keys simultaneously for one second or more and input the passcode.
Execution of the test mode is permitted according to the type of the passcode.
Passcode for service engineer [3214]: The test mode for the user type "service engineer" is permitted.

How to enter the normal mode
Press the [Home] key.
When the [Home] key is pressed, a buzzer for "confirmation of operation - confirmation of input" sounds and the Home screen is displayed.
Entering the normal mode is not allowed while a test mode is in process (from the test mode operation screen).

How to start a test mode: Selecting from the menu
Selecting a test mode (a [Test mode] button) starts the test mode.
The test mode operation screen differs depending on the processing type.
Filter the test modes to be displayed by specifying the processing type and category. Use the [Processing] buttons to specify the processing type and the [Category] button to specify the category.

Selecting a processing type
Selecting a [Processing] button puts it in the selected state and displays the test modes for the selected processing type.
The displayed test mode number has the number of the selected processing type.

Selecting a category
Selecting the [Category] button puts it in the selected state and displays the pop-up window for category selection. For the types of the [Category selection] buttons (individual categories) displayed in the pop-up window for category selection, refer to "Test mode number system". Buttons for options are always displayed (in the same manner as the categories of the main unit) even if they are not connected.
In the pop-up window, the category button that has been selected before the pop-up window is displayed is made in selected state. Selecting a [Category selection] button closes the pop-up window and displays the test modes of the selected category.
The [Category] button is selected and the selected category is displayed below the [Category] button.
The displayed test mode number has the number of the selected category (in the figure, [06] Transport section is selected and therefore [06] is displayed as the category number).
Selecting the [Category] button again and selecting the [All] button in the pop-up window displays [---] below the [Category] button and [00] as the category number.
Alvin
Posts: 60
Joined: Mon Feb 01, 2021 12:31 pm

Re: Riso ComColor FW5230

Postby Alvin » Tue Nov 09, 2021 12:03 pm

Riso ComColor FW5230, FW6231, FW5000, FW1230
How to end a test mode
Pressing the [Stop] key or [Close] button ([OK] and [Cancel] buttons in Data Edit (E)) in the test mode operation screen ends the test mode and the system returns to the test mode standby screen.
When the test mode is in pause, the [Stop] key and [Close] button are effective in any test mode.
Sensor Monitor (S) and Drive Check (D) accept the [Stop] key and [Close] button even while a test mode is in process.
Data Monitor (M) is not affected by ongoing processes and therefore accepts the [Stop] key and [Close] button any time.
Data Edit (E) is not affected by ongoing processes and therefore accepts the [Stop] key, [OK] button and [Close] button any time.
For how to end Unit Check (U) and Initialize (I), refer to the sections about how to end Unit Check (U) and Initialize (I).
After the test mode has ended, its number is displayed in the [Number] buttons in the test mode standby screen. The page shows the test mode that was last executed.
If you started the test mode from the menu, the selection (filtering) of the processing type and category returns to the selection before you started the test mode.
If you started the test mode with keys (by inputting numbers), the selection becomes one of the following states.
If the processing type and category were not selected (filtered) when you started the test mode, they return to the unselected (unfiltered) state.
If you started the test mode of the selected processing type/category, the processing type/category return to the selected state before you started the test mode.
If you started the test mode of any unselected (unfiltered) processing type/category, the processing type and category become the unselected (unfiltered) state.

Return to “Riso”

Who is online

Users browsing this forum: No registered users and 3 guests