Xerox Phaser 6510
Service mode. Diagnostics Functions Overview
Lists the diagnostic functions available to test or execute on the MFP and SFP.
| dC118 | Jam Counter | Displays the Count for jams that have occurred up to now. | MFP |
| dC120 | Failure Counter | Displays the Count for failures that have occurred up to now. | MFP |
| dC122 | Fault History | Displays the history in four categories: Document Feeder Jam, Paper Jam, Failure, and Last 40 Faults. | MFP & SFP |
| dC125 | Active Faults | Displays the Current Faults. | MFP |
| dC126 | System Registration Adjustment | Measures and adjusts registration to set correct positions. | MFP & SFP |
| dC131 | NVM Read / Write | To refer to the NVM data and set/modify it. | MFP & SFP |
| dC132 | Device ID / Billing Data | In cases where a serial number mismatch occurs, this function allows these errors to be corrected. MFP: This menu is always displayed. SFP: This menu is displayed only when the related error occurs. |
MFP & SFP |
| dC135 | HFSI Counter (For reference only) | Not needed for this product. Displays the Spec Life (threshold value) and the Current Value (usage status) of the periodic replacement parts. You can change the Spec Life and reset the Current Value. The Job History can be used to record/check the previous three replacements. | MFP & SFP |
| dC140 | Analog Component Monitoring | Monitors the Analog value of the A/D converter sensor, by operating the various components. | MFP & SFP |
| dC301 | Initialize NVM | To perform initialization for any NVM area. When initializing IOT area, the Back up/ Restore is necessary in dC363. | MFP & SFP |
| dC305 | Panel Diagnostics | To perform diagnosis of the LED / Audio which is implemented in the UI Panel. | MFP & SFP |
| dC330 | Component Control | Displays the logic state of Input Component input signals and operates the Output Components. | MFP & SFP |
| dC362 | Restore NVM Values | Do not use. This function does not operate. | MFP |
| dC363 | NVM Backup / Restore | To backup / restore the NVM Values (IOT areas). Use this command when exchanging the MCU. Do not use when exchanging the ESS. Also, use when initializing the IOT in dC301. | MFP & SFP |
| dC500 | Blank Page Threshold Value | To set the value that is used to determine what is a blank document when performing blank page detection for Fax machines. | MFP |
| dC612 | Print Test Pattern | To print the Test Pattern that is stored in the printer for checking image quality and isolating problems. | MFP & SFP |
| dC671 | Registration Measuring Cycle | Measures the color registration for four colors and displays the status with. | MFP & SFP |
| dC673 | Registration Control Sensor Check Cycle | To check if the misregistration detection system from the Regi Control (MOB Sensor) is operating normally. | MFP & SFP |
| dC675 | Registration Control Setup Cycle | To set the most appropriate Regi Control correction value for skew etc. at the first execution when replacing the LPH etc. | MFP & SFP |
| dC919 | Color Balance Adjustment | To perform fine adjustment of the center value of the Shadows/Midtones/Highlights output balance for each color Y, M, C and K (Black) for copy images. | MFP |
| dC924 | TRC Adjustment | Manual Density Adjustment manually sets the offset amount of the ADC-LUT created by the ADC patch and finely adjusts the gradation. | MFP & SFP |
| dC939 | Procon On / Off Print | The Procon On/Off Print consists of the following two modes. - “”: This is a Print mode that uses the current Procon Data with the Procon (Process Control) Soft enabled and the TRC Adjustment enabled. - “”: This is a Print mode that uses only the features possessed by the IOT and with the Procon, etc. all turned OFF. |
MFP & SFP |
| dC945 | IIT calibration | Do not use. This function does not operate. | MFP |
| dC991 | Toner Density Adjustment | Do not use. This function does not operate | MFP & SFP |
| dC1010 | Signals Sending Test | Do not use. This function does not operate. | MFP |
| dC1011 | Relay On / Off Test | Do not use. This function does not operate. | MFP |