Toshiba e-Studio 2051c

General description

Data cloning is a function that backs up user data, setting data and SRAM data into a USB device and also restores these data into the equipment. This function backs up or restores the data of the same equipment (same serial number), and is performed in the following cases.
- When the SYS board and the SRAM board are mistakenly replaced at the same time
- When the SRAM board is replaced
Notes:
The SYS board and SRAM board should never be replaced together.

Precautions

• When the ADI-HDD is initialized or replaced, back up the SRAM data afterwards.
• It is assumed that data cloning is to be performed when equipment is installed or options are installed. If the address book has been registered, do not perform restore. Registered / set data are lost.
• The USB device for the data cloning must meet the following conditions. A data cloning operation with any devices other than the following will not be guaranteed.
  • A combination USB device with a flash memory (to be connected directly to the USB port) and its capacity is 1GB or more.
  • A device compliant with the following specifications established by USB-IF (USB Implementers Forum)
    Class number: 8 (=08h) (Mass storage class)
    Sub-Class number: 6 (=06h) (SCSI transfer command set)
    Protocol number: 80 (=50h) (Bulk-only)
    The USB device should be formatted in the FAT or FAT32. (Correct operation cannot be guaranteed if it is formatted in NTFS/exFAT.)
  • Most of the common USB device are compliant with the above specifications and are therefore applicable to this data cloning. However, most of these devices were originally developed to be used in an environment for PCs (e.g. Windows or Macintosh) and thus operations exclusively with this equipment have not been fully guaranteed. Therefore, the user must thoroughly check in advance whether there will be any problem in operating with this equipment when adopting one of these devices.
• The USB device compliant with both USB 1.1 and USB 2.0 can be used for this data cloning.
• Data cloning with any storage devices other than a flash memory (e.g. USB-connectable memory card reader, CD/DVD drive, hard disk) will never be guaranteed. Therefore never use them for this operation.
• Be sure to unplug the LAN cable and Fax line before data are backed up / restored. Also, do not use the RADF and open the cover, drawer, etc. during the data cloning.
• Data can be backed up / restored only for the same model and version. If the version is different, update the firmware and back up / restore data in the same version.
• Restore data to equipment which has the same options as when the data are backed up.
• Delete the backed up data in the USB device after the data cloning.

Cloning procedure

Backup procedure

1. Press the [ON/OFF] button to shut down the equipment.
2. Connect the USB device [1] to the USB port [2] on the right upper cover.
   Notes: Backing up cannot be performed with multiple USB device [1] connected at the same time.
3. Turn the power ON while pressing [6] and the [CLEAR] button simultaneously.
4. When "SRAM Clear Mode" appears on the LCD, key in [0] to select "0. Set Serial Number" and then press the [START] button.
5. Key in the serial number on the label attached to the rear cover of the equipment, and then press the [OK] button.
6. "Serial Number Setting completed" is displayed.
7. Turn the power OFF.
8. Turn the power ON while pressing the [5] and [9] buttons simultaneously.
9. Enter the password, and then press the [OK] button. (If the password is not set for Service, press the [ENTER] button without entering anything.)
10. Select "1. Backup SRAM Data to USB", and then press the [START] button.
11. Enter a password (max. 15 characters) set for the backup data.
12. "Backup Successfully done Restore the MFP" is displayed on the LCD screen when the backup has been properly completed.
13. Press the [ON/OFF] button to shut down the equipment.

Restore procedure

1. Press the [ON/OFF] button to shut down the equipment.
2. Connect the USB device [1] to the USB port [2] on the right upper cover.
   Notes: Backing up cannot be performed with multiple USB device [1] connected at the same time.
3. Turn the power ON while pressing the [5] and [9] buttons simultaneously.
4. If "3" is set for 08-8911, enter the password.
5. Select "2. Restore SRAM Data from USB", and then press the [START] button.
6. Enter the password (max. 15 characters) which has been set in (6) of "[A] Backup procedure".
7. Enter the serial number for the backup file.
8. "Restore successfully done Restart the MFP" is displayed on the LCD screen when the restoring has been properly completed.
9. Press the [ON/OFF] button to shut down the equipment.

Notes:

To perform cloning with the SRAM data backed up before the ADI-HDD is initialized or replaced, follow the procedure below after the restoration is finished.

1. (1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.
2. Enter the password, and then press the [OK] button. (If no password is set for Service, press the [OK] button without entering anything.)
3. Key in [5] to select "5. Key Backup Restore", and then press the [START] button.
4. Key in [6] to select "6. ADIKey FROM to SRAM", and then press the [START] button.
5. Wait until the restoring of the encryption key is completed. "Operation Complete" is displayed.
6. Then turn the power OFF.