Sharp MXM950
Simulation mode. List of simulation codes 46 - 61
Main | Sub | Function (Purpose) | Section | Purpose |
---|---|---|---|---|
46 | 8 | Used to adjust the scanner color balance RGB. | Adjustment (Color scanner mode) |
|
9 | Used to adjust the copy density adjustment in the copy mode. | Adjust (DSPF mode) | ||
10 | Used to perform the engine gray balance manual adjustment. | Adjustment | ||
16 | Used to perform the engine color balance manual adjustment.(Monochrome, all modes) | Adjustment | ||
19 | Used to set the monochrome auto exposure mode. | Setting | ||
23 | Used to set the half-tone max. density correction. | Adjustment/ Setting | ||
24 | Used to adjust the engine half-tone auto density adjustment. | Adjustment | ||
32 | Adjustment of basic color density for AE mode | Adjustment/ Setting | ||
37 | Used to adjust B/W image forming. | Adjustment/ Setting | ||
39 | Used to adjust the image send sharpness. | Adjustment/ Setting | ||
40 | Used to collectively adjust all the FAX exposure modes. | Adjustment/ Setting | ||
41 | Used to adjust the FAX exposure (normal text). | Adjustment/ Setting | ||
42 | Used to adjust the FAX exposure (small text). | Adjustment/ Setting | ||
43 | Used to adjust the FAX exposure (fine). | Adjustment/ Setting | ||
44 | Used to adjust the FAX exposure (super fine). | Adjustment/ Setting | ||
45 | Used to adjust the FAX exposure (600 dpi) | Adjustment/ Setting | ||
47 | Used to set the JPEG compression rate in copying and scanning. | Adjustment/ Setting | ||
48 | 1 | Used to adjust the copy magnification ratio (main/sub scanning direction). | Adjustment | |
5 | Used to adjust the copy magnification ratio (sub scanning direction).This adjustment is performed when Sim. 48-1 is used to adjust the sub scanning direction magnification ratio and a copy is made in a different copy magnification ratio and a satisfactory result is not obtained. | Scanner section | Adjustment | |
49 | 1 | Firmware update | ||
3 | Used to update the instruction manual stored in the HDD. | |||
50 | 1 | Used to adjust copy image position on print paper and the void area (image loss) in the copy mode. (The similar adjustment can be performed with Sim. 50-5 and Sim. 50-2 (Simple method). (Document table mode)) | Adjustment | |
2 | Used to adjust the copy image position on the paper and the void area (image loss) in the copy mode. (This simulation, similar to Sim. 50-1, provides more simplified adjustment.) | Adjustment | ||
5 | Used to adjust the printer print lead edge. | Adjustment | ||
6 | DSPF document lead edge adjustment Used to adjust the copy image position on print paper and the void area (image loss) in the copy mode. (The similar adjustment can be performed with Sim. 50-7 (Simple method).) (DSPF mode) | DSPF | Adjustment | |
7 | DSPF document lead edge adjustment (Simple method) Used to adjust the copy image position on print paper and the void area (image loss) in the copy mode. (Sim. 50-6 simple method) | DSPF | Adjustment | |
10 | Used to adjust the print image off-center position. (The adjustment is made for each paper feed section.) | Adjustment | ||
12 | Used to adjust the scan image off-center position. (The adjustment is made for each scan mode.) | Adjustment | ||
27 | Used to adjust the image loss of a scan image in the FAX/ Scanner mode. | Adjustment | ||
28 | Used to perform the OC adjustment, the BK main scan magnification ratio correction, the DSPF adjustment, and the print position adjustment. | Adjustment | ||
51 | 2 | Used to adjust the contact pressure of paper against the resist roller (main unit paper feed, duplex paper feed, DSPF paper feed) in each section. (This adjustment is required when there is a great variation in the print image position for the paper or when paper jam occurred.) | Adjustment/ Setting | |
53 | 6 | Used to adjust the DSPF width detection level. | Adjustment | |
7 | Used to set the DSPF width adjustment value. (Sim. 53-6 manual input) | Adjustment/ Setting | ||
8 | Used to adjust the DSPF document scan start position. | Adjustment | ||
12 | Used to check the operations of the DSPF double feed sensor. | (Must not be used unless a special change is required.) | ||
55 | 1 | Used to set the specifications of the engine control operation. | (Must not be used unless a special change is required.) | |
2 | Used to set the specifications of the scanner control operation. | (Must not be used unless a special change is required.) | ||
3 | Used to set the specifications of the controller operation. | (Must not be used unless a special change is required.) | ||
10 | Used to enter the special stamp text input. | Special stamp text setting | ||
56 | 1 | Used to transfer data (which is used in PWB repair). | Backup | |
2 | Used to back up the data (including user authentication data and address book data) in the EEPROM, the SRAM, and the HDD on the main unit to the USB memory and to transfer the data. | Backup | ||
3 | Used to back up the document filing data. | Backup | ||
4 | Used to back up the job log data. | Backup | ||
60 | 1 | Used to check the operations (read/ write) of the MFP control (SDRAM). | Operation test/check | |
2 | Used to set the onboard SDRAM. | (This simulation is normally not used in the market.) | ||
61 | 1 | Used to check the polygon motor rotation and the BD signal detection. | Adjustment/ Setting | |
3 | Used to set the laser power. | Adjustment/ Setting |