Sharp MXM450
Simulation mode. List of simulation codes 46 - 64
| Code | Function (Purpose) | |
|---|---|---|
| Main | Sub | |
| 46 | 15 | Used to adjust the print density in the FAX mode (each super fine mode). (Only when FAX is installed.) |
| 16 | Used to adjust the print density in the FAX mode (each ultra fine mode). (Only when FAX is installed.) | |
| 17 | Used to set the gain in shading correction. | |
| 18 | Used to adjust the gamma (density gradient) in the copy mode. | |
| 19 | Used to set the auto mode operation specifications in each mode (copy, scan, FAX). | |
| 20 | Used to adjust the copy density correction in the SPF copy mode for the document table copy mode. The adjustment is made so that the copy density becomes the same as that of the document table copy mode. | |
| 21 | Used to adjust the scanner exposure level in all the scanner modes. | |
| 22 | Used to adjust the scanner exposure level in the normal text mode. | |
| 23 | Used to adjust the scanner exposure level in the fine text mode. | |
| 24 | Used to adjust the scanner exposure level in the super fine text mode. | |
| 25 | Used to adjust the scanner exposure level in the ultra fine text mode. | |
| 27 | Used to adjust the gamma (density gradient) of the network scanner mode. | |
| 31 | Used to adjust sharpness of the copy mode. | |
| 39 | Used to adjust sharpness of the FAX mode. | |
| 45 | Used to adjust the image density in the FAX mode (600dpi). | |
| 46 | Used to adjust sharpness of the scanner mode. | |
| 48 | 1 | Used to adjust the copy magnification ratio (in the main scanning and the sub scanning directions). |
| 5 | Used to adjust the copy magnification ratio in the sub scanning direction. | |
| 6 | HSYNC cycle adjustment | |
| 49 | 1 | Firmware updating |
| 50 | 1 | Used to adjust the copy image position and the void area (image loss) adjustment on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-5 and 50-2 (Simplified method).) (Document table mode) |
| 2 | Used to adjust the document scan position, the image print position, and the void area (image loss). (Simple adjustment) (This adjustment is the simple method of SIM 50-1.) (Document table mode) | |
| 5 | Used to adjust the print image position and the void area (image loss) on print paper. (Adjustment as the print engine) (This adjustment is reflected on all the FAX/printer/copy modes.) | |
| 6 | Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-7 (simple method).) (SPF mode) |
|
| 7 | Used to adjust the copy image position and void area (image loss) on print paper in the copy mode. (The similar adjustment can be performed with SIM 50-6.) (SPF mode) |
|
| 10 | Used to adjust the print image off-center position. (Adjusted separately for each paper feed section.) | |
| 12 | Used to adjust the scan image off-center position. (Adjusted separately for each scan mode.) | |
| 27 | Used to adjust the image loss of the scan image in the FAX/scan mode. | |
| 51 | 2 | Used to adjust the contact pressure of paper on the resist roller of each section (each paper feed, duplex feed and SPF paper feed of the copier). (This adjustment is required when the print image position variations are considerably great or when paper jams occur frequently.) |
| 53 | 6 | Used to adjust the DSPF width detection level. |
| 7 | Used to enter the SPF width detection adjustment value. | |
| 8 | Used to adjust the document scan start position. (Used to adjust the scanner scan position in the SPF mode front scan.) | |
| 55 | 1 | Used to set the specifications of the engine control operations. (PCU PWB) |
| 2 | Used to set the specifications of the scanner control operations. (Scanner control PWB) | |
| 3 | Used to set the specifications of the controller operations. (MFP control PWB) | |
| 56 | 1 | Used to transfer the MFP controller data. (Used to repair the PWB.) |
| 60 | 1 | Used to check the MFP control (DRAM) operations (read/write). |
| 61 | 1 | Used to check the operation of the scanner (write) unit (LSU). |
| 2 | Used to adjust the laser power (absolute value) in the copy mode. | |
| 3 | Used to adjust the laser power (absolute value) in the FAX mode. | |
| 4 | Used to adjust the laser power (absolute value) in the printer mode. | |
| 62 | 1 | Used to format the hard disk. (Only in the model with a disk installed) |
| 2 | Used to check the operation of the hard disk (read/ write). (Only in the model with a disk installed) (Partial check) | |
| 3 | Used to check the operation of the hard disk (read/ write). (Only in the model with a disk installed) (All areas check) | |
| 6 | Used to check the operations of the hard disk. (The self diag operation of the SMART function is executed.) (Only in the model with a disk installed) |
|
| 7 | Used to check the operations of the hard disk. (The result of the self diag operation of the SMART function is printed out.) (Only in the model with a disk installed) |
|
| 8 | Used to format the hard disk (the system area excluded). (Only in the model with a disk installed) | |
| 9 | Used to format the hard disk (the system area). (Only in the model with a disk installed) | |
| 10 | Used to delete a job complete list (also to delete job log data) (Only in the model with a disk installed) | |
| 11 | Used to delete document filing data. (The management area (standard folder, user folder) is cleared.) (Only in the model with a disk installed) | |
| 63 | 1 | Used to check the result of shading correction. (The shading correction data are displayed.) |
| 2 | Used to execute shading. | |
| 7 | Used to adjust the white plate scan start position for shading. (Document table mode) | |
| 64 | 1 | Used to check the operation of the printer section (self-print operation), (The print pattern, the paper feed mode, the print mode, the print quantity, and the density can be optionally set.) |