Sharp MXM450
Simulation mode. List of simulation codes 24 - 46
| Code | Function (Purpose) | |
|---|---|---|
| Main | Sub | |
| 24 | 3 | Used to clear the number of use of the finisher, SPF, and the scan (reading) unit. |
| 4 | Used to reset the maintenance counter. | |
| 5 | Used to reset the developer counter. (The developer counter of the DV unit which is installed is reset.) | |
| 6 | Used to reset the copy counter. | |
| 7 | Used to clear the OPC drum counter. (Perform this simulation when the OPC drum is replaced.) | |
| 9 | Used clear the printer mode print counter and the self print mode print counter. | |
| 10 | Used to clear the FAX counter. (Only when FAX is installed) | |
| 11 | Used to reset the OPC drum rotation time, and the DV unit rotation time counter. The developer counter in the DV unit installed is reset. | |
| 15 | Used to clear the counters related to the scan mode and the Internet FAX mode. | |
| 25 | 1 | Used to check the operations of the developing section (toner concentration, humidity and toner concentration sensor, humidity sensor, temperature sensor output can be monitored.) |
| 2 | Used to make the initial setting of toner concentration when replacing developer. | |
| 26 | 3 | Used to set the specifications of the auditor. Setting must be made according to the auditor use conditions. |
| 5 | Used to set the count mode of the total counter and the maintenance counter. | |
| 6 | Used to set the specifications (paper, document detection, etc.) of the destination. | |
| 10 | Used to set the network scanner trial mode. | |
| 18 | Used to set YES/NO of toner save operation. (This function is valid only in Japan and UK versions. (Depends on the destination setting of SIM26-6.) For the other destinations, the same setting can be made by the user program P22.) | |
| 30 | Used to set the operation mode conforming to the CE mark (Europe safety standards). (Conforming to soft start when driving the fusing heater lamp.) | |
| 35 | Used to set whether the same continuous troubles are displayed as one trouble or the series of troubles with SIM 22-4 when the same troubles occur continuously. | |
| 38 | Used to set CONTINUE/STOP of printing when maintenance timing is over and the count value reaches 110% of replacement timing (life). | |
| 41 | Used to set the automatic magnification ratio selection (AMS) in the pamphlet mode. | |
| 50 | Black-White reverse YES/NO setting (Except for UK) | |
| 52 | Used to set whether non-print paper (insertion paper, cover paper) (blank image print paper) is counted up or not. | |
| 68 | Used to set ENABLE/DISABLE of the CA key cancel function of print stop. | |
| 27 | 1 | Used to set the specifications for operations in case of communication trouble between the host computer and MODEM (machine side). (When communication trouble occurs between the host computer MODEM and the machine, the self diag display (U7-00) is printed and setting for inhibition of print or not is made.) |
| 5 | Used to enter the machine tag No. (This function allows to check the tag No. of the machine with the host computer.) | |
| 30 | 1 | Used to check the operation of sensors and detectors in other than the paper feed section and the operations of the related circuits. |
| 2 | Used to check the operation of sensors and detectors in the paper feed section and the related circuits. | |
| 40 | 1 | Used to check the operation of the manual feed tray paper size detector and the related circuit. (The operation of the manual feed tray paper size detector can be monitored with the LCD display.) |
| 2 | Used to adjust the manual paper feed tray paper width detector detection level. | |
| 7 | Used to enter the manual paper feed tray paper width adjustment value. | |
| 11 | Used to check the multi-purpose tray width detection level. | |
| 12 | Used to adjust the multi-purpose tray width detection level. | |
| 41 | 1 | Used to check the operation of the document size sensor and the related circuit. (The operation of the document size sensor can be monitored with the LCD display.) |
| 2 | Used to adjust the document size sensor sensing level. | |
| 3 | Used to check the operation of the document size sensor and the related circuit. (The document size sensor output level can be monitored with the LCD display.) | |
| 43 | 1 | Used to set the fusing temperature in each operation mode. |
| 44 | 1 | Used to set enable/disable of correction operations in the image forming (process) section. |
| 4 | Used to set the target image (reference) density level in the developing bias voltage correction. | |
| 9 | Used to check the data related to the image forming section correction (process correction) result (corrected main charger grid voltage, the developing bias voltage, and the laser power voltage in each print mode). (This simulation allows to check that correction is performed normally or not.) | |
| 14 | Used to check the output level of the temperature sensor and the humidity sensor. | |
| 16 | Used to check the toner concentration control data. | |
| 46 | 2 | Used to adjust the copy density in all the copy modes (Auto, Text, Text/Photo, and Photo mode). |
| 9 | Used to adjust the print density for each density level (display value) in the copy mode (binary - Text mode). An optional print density can be set for each density level (display value). | |
| 10 | Used to adjust the print density for each density level (display value) in the copy mode (binary - Text/Photo mode). An optional print density can be set for each density level (display value). | |
| 11 | Used to adjust the print density for each density level (display value) in the copy mode (binary - Photo mode). An optional print density can be set for each density level (display value). | |
| 12 | Used to adjust the print density in the FAX mode (all modes). | |
| 13 | Used to adjust the print density in the FAX mode (each normal mode). (Only when FAX is installed.) | |
| 14 | Used to adjust the print density in the FAX mode (each fine mode). (Only when FAX is installed.) | |