Sharp MXM450
Simulation mode. List of simulation codes 1 - 24
| Code | Function (Purpose) | |
|---|---|---|
| Main | Sub | |
| 1 | 1 | Used to check the operations of the scanner (read) unit and its control circuit. |
| 2 | Used to check the operation of sensor and detector in the scanning (read) section and the related circuit. | |
| 2 | 1 | Used to check the operations of the automatic document feeder unit and the control circuit. |
| 2 | Used to check the operations of the sensors and detectors in the automatic document feeder unit and the related circuits. | |
| 3 | Used to check the operations of the loads in the automatic document feeder unit and the control circuits. | |
| 3 | 2 | Used to check the operation of sensor and detector in the finisher and the related circuit. |
| 3 | Used to check the operation of the load in the finisher and the control circuit. | |
| 6 | Used to adjust the stacking capacity of the finisher. (Used to adjust the alignment plate (jogger) stop position in the finisher paper width direction. The adjustment is made by changing the alignment plate home position in the paper width direction by software.) | |
| 10 | Console finisher adjustment | |
| 20 | Used to check the mail bin stacker sensor. | |
| 21 | Used to check the operations of the mail bin stacker loads. | |
| 4 | 2 | Used to check the operations of the sensors and detectors in the paper feed section (desk paper feed/large capacity tray) and the related circuit. |
| 3 | Used to check the operations of the loads in the paper feed section (desk paper feed/large capacity tray) and the related circuit. | |
| 5 | 1 | Used to check the operation of the display, LCD in the operation panel, and control circuit. |
| 2 | Used to check the operation of the heater lamp and the control circuit. | |
| 3 | Used to check the operation of the scanner lamp and the control circuit. | |
| 6 | 1 | Used to check the operation of the paper transport system loads and the control circuit. |
| 2 | Used to check the operations of each fan motor and its control circuit. | |
| 7 | 1 | Used to set the operating conditions of aging. |
| 6 | Used to set the intermittent aging cycle. | |
| 8 | Used to set the warm-up time display YES/NO. | |
| 8 | 1 | Used to check and adjust the operations of the developing voltage of each color and the control circuit. |
| 2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. | |
| 6 | Used to check and adjust the operation of the transfer voltage and the control circuit. | |
| 17 | Used to check and adjust the operation of the transfer voltage and the related circuit. (Transfer belt cleaning mode) | |
| 9 | 1 | Used to check and adjust the operation of the load (clutch/solenoid) in the duplex section and the control circuit. |
| 2 | Used to check the operations of the sensors and detectors in the duplex section and its control circuit. | |
| 10 | 1 | Used to check the operations of the toner motor and the related circuit. |
| 13 | 0 | Used to cancel the self-diag "U1" trouble. (Only when FAX is installed.) |
| 14 | 0 | Used to cancel excluding the self-diag U1/LCC/U2/ PF troubles. |
| 15 | 0 | Used to cancel the self-diag "U6-01,02, 03, F3-12, 22" (large capacity paper feed tray, paper feed trays 1, 2) troubles. |
| 16 | 0 | Used to cancel the self-diag U2 troubles. |
| 17 | 0 | Used to cancel the PF troubles (when the copy inhibit command from the host computer is received). |
| 21 | 1 | Used to set the maintenance cycle. |
| 22 | 1 | Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) |
| 2 | Used to check the total numbers of misfeed and troubles. (When the number of misfeed is considerably great, it is judged as necessary for repair. The misfeed rate is obtained by dividing this count value with the total counter value.) | |
| 3 | Used to check misfeed positions and the misfeed count of each position. (If the misfeed count is considerably great, it may be judged as necessary to repair.) | |
| 4 | Used to check the trouble (self diag) history. | |
| 5 | Used to check the ROM version of each unit (section). | |
| 6 | Used to output the list of the setting and adjustment data (simulations, FAX soft switch, counters). | |
| 7 | Used to display the key operator code. (This simulation is used when the customer forgets the key operator code.) | |
| 8 | Used to check the number of use of the finisher, the SPF, and the scan (reading) unit. | |
| 9 | Used to check the number of use (print quantity) of each paper feed section. | |
| 10 | Used to check the system configuration (option, internal hardware). | |
| 11 | Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) | |
| 12 | Used to check the SPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) | |
| 13 | Used to check the operating time of the process section (OPC drum, DV unit, toner bottle). | |
| 19 | Used to check the values of the counters related to the scan mode and the Internet FAX mode. | |
| 30 | OSA vendor ID display (Application Communication Module) |
|
| 31 | OSA vendor ID display (External account module) | |
| 23 | 2 | Used to check the trouble history of paper jam and misfeed. (If the number of misfeed and troubles is considerably great, it may be judged as necessary to repair.) |
| 80 | Used to check the operations of the sensors and detectors in the paper feed and transport section. | |
| 24 | 1 | Used to clear the misfeed counter, the misfeed history, the trouble counter, and the trouble history. (The counters are cleared after completion of maintenance.) |
| 2 | Used to clear the number of use (the number of prints) of each paper feed section. | |