PrintCopy.info service

Sharp MXM2651

Simulation mode. List of codes 63-67

>
Main Sub Functions Section
62 9 Used to delete the storage data.  
12 Used to set the automatic format at storage trouble.  
14 Used to delete the document filing management data. HDD
21 Used to display the information on the MFP storage.  
63 1 Used to display the shading correction result. Scanner
2 Used to perform shading.  
3 Used to perform scanner (CCD) color balance and gamma auto adjustment. Scanner
4 Used to display the SIT chart patch density.  
5 Used to perform the scanner (CCD) color balance and gamma default setting.  
11 Used to set the target color balance of the copy mode auto color balance adjustment.  
64 2 Test print. (Self print) (Monochrome mode)  
4 Printer test print. (Self print)  
5 Printer test print. (Self print) (PCL)  
6 Printer test print. (Self print) (PS)  
65 1 Used to adjust the touch panel (LCD display section) detection coordinates. Operation panel section
2 Used to display the touch panel (LCD display section) detection coordinates.  
5 Used to check the operation panel key input.  
66 1 Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking with the LCD. FAX
2 Used to enter a country code and set the default value for the country code. FAX
3 Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the result. FAX
4 Used to send the selected signals to the line and the main unit speaker. (Send level: max.) FAX
5 Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting) (For the kinds of send signals, refer to SIM66-04.) FAX
6 Used to print the confidential registration check table (BOX NO., BOX name, pass code. (If there is no confidential registration, no print is made.) FAX
7 Used to output all image data saved in the image memory. (Confidential data are also outputted.) FAX
8 Used to send the selected sound messages to the line and the speaker. (Send level: Max.) FAX
9 Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting)
* For details of sound messages, refer to the sound message table of SIM66-08.
FAX
10 Used to clear the FAX and image send image data. (The confidential data are also cleared.) FAX
11 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.) FAX
12 Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting)
* For the kings of send signals at 300bps, refer to SIM66-11, 300bps send signal table.
FAX
13 Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.) FAX
14 Used to execute the dial pulse (10PPS) send test and to adjust the make time. FAX
15 Used to execute the dial pulse (20PPS) send test and to adjust the make time. FAX
16 Used to execute the DTFM signal send test and to adjust the send level. FAX
17 Used to send the DTMF signal to the line and the speaker. (Send level: Max.) FAX
18 Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting) FAX
21 Used to print the selected items (system error, protocol monitor). FAX
22 Used to set the handset sound volume. (This simulation can be executed even though the handset setting is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.)
(Japan model only)
FAX
29 Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion table, the group expansion table, the program registration table, the interface memory box table, the meta data, InboundRouting, and the DocumentAdmin table). FAX
30 Used to display the TEL/LIU status change, The display is highlighted by status change. FAX
31 Used to set ON/OFF the port for output to TEL/LIU. FAX
32 Used to check the fixed data received from the line and to display the result. FAX
33 Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected, the display is highlighted. FAX
36 Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the command line individually. FAX
39 Used to check and change the destination setting saved in EEPROM of the FAX BOX. FAX
42 Used to rewrite the program to power control installed in the FAX BOX. FAX
43 Used to write the adjustment value into the power control installed in the FAX BOX. FAX
61 Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while checking with the LCD. FAX
62 Used to import the FAX receive data into a USB memory in PDF file type. FAX
67 17 Printer reset Printer
24 Printer gray balance adjustment (Auto adjustment) Printer
25 Printer gray balance adjustment (Manual adjustment) Printer
26 Used to set the target gray balance of the printer mode auto color balance adjustment. Printer
31 Used to clear the printer calibration value. Printer
33 Used to change the gamma of the printer screen. Printer
34 Used to set the density correction in the printer high density section. (Support for the high density section tone gap) Printer
36 Used to adjust the density in the low density section. Printer
46 Used to adjust the printer image enhancement.  
52 Used to set the default of the gamma of the printer screen. Printer
54 Printer gray balance adjustment (Automatic adjustment for each dither) Printer
Error Code
Service Mode, Troubleshooting
Parts Catalog
Compatibility
Downloads Files
Home
New Register Forgot Password?
Send message to us