Sharp MXM260N
Simulation mode. List of simulation codes 26 - 46
Code | Function | |
---|---|---|
Main | Sub | |
26 | 1 | Used to set whether the job separator is installed or not. (Since this cannot be detected by hardware detection, it is set in this simulation.) |
2 | Used to set whether the automatic detection of paper size is made or not. | |
3 | Used to set the specifications of the auditor. Setting must be made depending on the use condition of the auditor. |
|
5 | Used to set the count mode of the total counter and the maintenance counter. | |
6 | Used to set the specifications depending on the destination. | |
10 | Network scanner trial mode setting | |
12 | Used to input the Software Key for E-MAIL RIC. | |
14 | Used to input the Software Key for the PS extension kit. | |
18 | Used to set enable/disable of toner save operation. | |
22 | Used to set the specification (language display) for the destination. | |
30 | Used to set ON/OFF of the heater lamp slow-up control conforming to the CE mark control. | |
35 | Used to set whether the same continuous troubles are displayed as one trouble or the series of troubles with SIM 22-4 when the same troubles occur continuously. | |
36 | Used to set whether the machine is stopped or not when the maintenance counter life is expired. | |
50 | Used to set ON/OFF of the black and white reversion function. | |
56 | Gamma life correction setting | |
57 | Used to set the model code. | |
60 | Used to set enable/disable of the FAX mode key when FAX is not installed. (When FAX is installed, the FAX mode is enabled regardless of this setup.) | |
69 | Toner near end setting | |
71 | In the power save time setting, the pre-heat (preĀheat mode setting) and the auto power shut off time can be set to the short time setup (pre-heat: 1 min, auto power shut off: 4 min) and the long time setup (pre-heat: 15min, auto power shut off: 60min). |
|
72 | The letterhead support is set. When "Letterhead paper setting" is selected, the set value of SIM 26-46 (Image output direction setting) is set to "Setting Enable" accordingly. |
|
27 | 1 | Used to set PC/MODEM communication trouble (U7-00) detection Yes/No. |
2 | Sender's registration number/HOST server TEL number. | |
4 | Function setting | |
5 | Used to set the tag number | |
7 | FSS function setting | |
9 | FSS function adjustment | |
10 | Trouble precognition history clear | |
14 | FSS connection test setting | |
15 | Displays status of FSS connection | |
30 | 1 | Used to display the sensor status attached to the machine. |
2 | Used to display the status of the sensors attached to the standard tray and the manual feed tray. (Use SIM 4-2 for the option trays.) The sensor of an uninstalled tray is not displayed. |
|
40 | 1 | Used to check the sensor of the machine manual feed tray. |
2 | Used to adjust the manual paper feed tray paper width detector detection level. | |
3 | The AD conversion value of manual feed width detection is displayed. | |
41 | 1 | Used to check the document size detection photo sensor. |
2 | Used to adjust the detection level of the document size photo sensor. | |
3 | Used to check the light reception level and the detection level of the original size detection photo sensor. | |
4 | Used to adjust the detection level of OC 20 degrees. | |
43 | 1 | Used to set the fusing temperature. |
10 | Used to set the paper feed cycle timing when printing postcards. | |
44 | 1 | Used to make various setups in each mode of process control. |
2 | Drum life correction setting | |
3 | Used to set the DV count correction. | |
9 | Used to display the process control correction information. | |
14 | Used to display the environment (temperature, humidity) correction information. | |
16 | Used to set the toner density control correction value. | |
17 | Used to display the toner density control reference value. | |
34 | Used to set the transfer current value in each mode. | |
40 | Used to set the time from the start of the main motor rotation (Ready) to the start of toner supply in previous rotation after turning on the power. | |
46 | 2 | Used to set the exposure level in each exposure mode. |
9 | Used to adjust the shift amount and the inclination value for each level (1 to 5) of the exposure mode (Text). | |
10 | Used to adjust the shift amount and the inclination value for each level (1 to 5) of the exposure mode (Text/Photo). | |
11 | Used to adjust the shift amount and the inclination value for each level (1 to 5) of the exposure mode (Photo). | |
12 | FAX exposure level adjustment (1 mode automatic adjustment) | |
13 | FAX exposure level adjustment (Normal mode individual adjustment) | |
14 | FAX exposure level adjustment (Fine text mode individual adjustment) | |
15 | FAX exposure level adjustment (Super Fine mode individual adjustment) | |
16 | FAX exposure level adjustment (Ultra Fine mode individual adjustment) | |
18 | Used to adjust inclination for each exposure mode. | |
19 | Used to set the control method of the exposure mode. | |
20 | Used to set the exposure correction value of SPF/ RSPF for OC exposure. | |
30 | Used to set the AE and the limit value in AE (Toner save). | |
31 | Used to set the AE and the limit value in AE (Toner save). | |
39 | Used to switch the FAX send image quality. |