Sharp MXM232DY
Simulation mode. List of codes 1-30
Main code | Sub code | Contents |
---|---|---|
01 | 01 | Mirror scanning operation |
02 | Mirror home position sensor (MHPS) status display | |
02 | 01 | Single paper feeder (SPF)/Reversing single pass feeder(RSPF) aging *2 |
02 | SPF/RSPF sensor status display *2 | |
03 | SPF/RSPF motor operation check *2 | |
08 | SPF/RSPF paper feed solenoid operation check *2 | |
09 | RSPF reverse solenoid operation check *2 *3 | |
11 | SPF/RSPF PS release solenoid operation check *2 | |
03 | 02 | Shifter/job separator sensor status display |
03 | Shifter operation check | |
04 | Job separator operation check *4 | |
11 | Shifter home position check | |
05 | 01 | Operation panel display check |
02 | Fusing lamp and cooling fan operation check | |
03 | Copy lamp lighting check | |
06 | 01 | Paper feed/transport solenoid operation check |
02 | Resist roller solenoid (RRS) operation check | |
07 | 01 | Warm-up display and aging with jam detection |
06 | Intermittent aging | |
08 | Shifting with warm-up display | |
08 | 01 | Developing bias output |
02 | Main charger output (Grid = HIGH) | |
03 | Main charger output (Grid = LOW) | |
06 | Transfer charger output | |
09 | 01 | Duplex motor forward rotation check *6 |
02 | Duplex motor reverse rotation check *6 | |
04 | Duplex motor RPM adjustment *6 | |
05 | Duplex motor switchback time adjustment | |
10 | - | Toner motor operation |
14 | - | Trouble cancel (except for U2) |
16 | - | U2 trouble cancel |
20 | 01 | Maintenance counter clear |
21 | 01 | Maintenance cycle setting |
22 | 01 | Counters display |
03 | Jam memory display | |
04 | Jam total counter display | |
07 | System setting code display | |
09 | Paper feed counter display | |
11 | FAX-related counter display | |
13 | CRUM destination display *5 | |
14 | P-ROM version display | |
15 | Trouble memory display | |
22 | SPF/RSPF jam counter display *2 | |
24 | 01 | Jam total counter clear |
02 | Trouble memory clear | |
04 | SPF/RSPF counter clear *2 | |
05 | Duplex print counter clear *6 | |
06 | Paper feed counter clear | |
07 | Drum counter clear | |
08 | Copy counter clear | |
09 | Printer counter clear | |
10 | FAX-related counter clear | |
13 | Scanner counter clear | |
14 | SPF/RSPF jam total counter clear *2 | |
15 | Scanner mode counter clear | |
25 | 01 | Main motor operation check (Cooling fan motor rotation check) |
02 | Auto developer adjustment (Initial setting of toner density when replacing developer) | |
10 | Polygon motor operation check | |
26 | 01 | Job separator setting |
02 | Size setting | |
03 | Auditor setting | |
04 | Copier duplex setting | |
05 | Count mode setting | |
06 | Destination setting | |
07 | Machine condition check | |
08 | Manual transfer shaking countermeasures setting | |
18 | Toner save mode setting | |
20 | Job separator paper exit mode setting | |
22 | Language setting clear | |
30 | CE mark conformity control ON/OFF | |
31 | Auditor mode exclusive setup | |
36 | Cancel of stop at maintenance life over | |
37 | Cancel of stop at developer life over | |
39 | Memory capacity check | |
42 | Transfer ON/OFF timing control setting | |
43 | Side void amount setting | |
51 | Copy temporary stop function setting | |
54 | LCD contrast PWM duty setting | |
56 | Life correction ON/OFF setting | |
60 | [FAX] key Enable/Disable setting | |
69 | Toner near end environment setting | |
73 | Toner save setting display/non-display | |
74 | Total counter display change setting | |
30 | 01 | Paper sensor status display |
Execution inhibit conditions
*1) Execution is inhibited when the duplex setup is OFF and other than RSPF is set.
*2) Execution is inhibited when OC.
*3) Execution is inhibited when SPF. (Not RSPF)
*4) Execution is inhibited when the job separator is not installed.
*5) Execution is inhibited when the model is not provided with the CRUM.
*6) Execution is inhibited when the duplex setup is OFF.