Sharp MXM232DA
Simulation mode. List of codes 41-67
Main code | Sub code | Contents |
---|---|---|
41 | 01 | Document size detection photo sensor check |
02 | Document size detection photo sensor detection level adjustment | |
03 | Document size detection photo sensor light receiving/ detection level check | |
04 | Detection level adjustment when the document size is settled(15degrees - 20degrees) | |
42 | 01 | Developing counter clear |
43 | 01 | Fusing temperature setting 1 |
02 | Fusing temperature setting 2 | |
03 | Fusing temperature setting 3 | |
04 | Fusing temperature setting 4 | |
12 | Standby mode fusing fan rotation setting | |
13 | Paper interval control allow/inhibit setting | |
44 | 01 | Enable/Disable setting of toner density control correction |
16 | Toner density control data check and toner density correction quantity display | |
34 | Transfer current setting | |
46 | 02 | Copy density adjustment (600dpi) |
10 | Copy exposure level adjustment, individual setting (Text) 600dpi | |
11 | Copy exposure level adjustment, individual setting (Photo) 600dpi | |
12 | Density adjustment in the FAX mode (Collective adjustments) | |
13-16 | Density adjustment in the FAX mode (Individual adjustments) | |
19 | Exposure mode setting (Gamma table setting/AE operation mode setting/ Photo image process setting) |
|
20 | SPF/RSPF exposure correction *2 | |
29 | Image contrast adjustment (600dpi) | |
30 | AE limit setting | |
31 | Image sharpness adjustment | |
39 | FAX IMAGE adjustment | |
48 | 01 | Main/sub scanning magnification ratio adjustment |
05 | SPF/RSPF mode sub scanning magnification ratio adjustment in copying *2 | |
08 | FAX magnification ratio adjustment (scan) | |
09 | FAX magnification ratio adjustment (print) | |
49 | 01 | Flash ROM program writing mode (MCU) |
02 | Flash ROM program writing mode (NNB) | |
50 | 01 | Image lead edge adjustment |
06 | Copy lead edge position adjustment (SPF/RSPF) *2 | |
8 | FAX lead edge adjustment (scan) | |
10 | Print off-center adjustment | |
12 | Document off-center adjustment | |
18 | Memory reverse position adjustment in duplex copy *1 | |
19 | Rear edge void adjustment in duplex copy *5 | |
51 | 02 | Resist amount adjustment |
53 | 08 | SPF/RSPF scanning position automatic adjustment *2 |
61 | 02 | Laser power correction ON/OFF (Invalidity) |
03 | HSYNC output check | |
63 | 01 | Shading check |
64 | 01 | Self print |
65 | 10 | Key ACK time setting display/non-display setting |
11 | Info lamp setting | |
66 | 01 | FAX soft SW setting |
02 | FAX soft SW initializing | |
03 | FAX PWB memory check | |
04 | Signal send mode | |
06 | Confidential pass code print | |
07 | Image memory content output | |
10 | Image memory contents clear | |
11 | 300bps signal send | |
13 | Dial number registration | |
17 | DTMF signal send | |
21 | FAX information print | |
24 | FAST SRAM clear | |
30 | TEL/LIU status change check | |
31 | TEL/LIU setting | |
32 | Receive data check | |
33 | Signal detection check | |
34 | Communication time measurement | |
37 | Speaker sound volume adjustment | |
38 | Time setting/check | |
42 | PC program writing | |
43 | PIC adjustment value writing | |
52 | Pseudo ringer check | |
67 | 50 | USB reception speed adjustment |
Execution inhibit conditions
*1) Execution is inhibited when the duplex setup is OFF and other than RSPF is set.
*2) Execution is inhibited when OC.
*3) Execution is inhibited when SPF. (Not RSPF)
*4) Execution is inhibited when the job separator is not installed.
*5) Execution is inhibited when the model is not provided with the CRUM.
*6) Execution is inhibited when the duplex setup is OFF.