Sharp MXC382SC
Simulation mode. Codes Color model 46-62
| Main | Sub | Functions | Section |
|---|---|---|---|
| 46 | 52 | Used to reset the copy color balance adjustment (adjustment for each dither) to the default value. (The set values of SIM46-51 and SIM46-54 are set to the default values.) (Only color model) | |
| 54 | Used to reset the copy color balance adjustment (auto adjustment for each dither). (Only color model) | ||
| 55 | Used to adjust the range of colors reproduced in drop-out colors. | ||
| 60 | Used to adjust the sharpness in the color auto copy mode. | ||
| 61 | Used to adjust the area separation recognition level. | ||
| 62 | Used to set the operating conditions of the ACS, the area separation, the background image process, and the auto exposure mode. | ||
| 63 | Used to adjust the density in the copy low density section. | ||
| 74 | Copy color balance adjustment (Auto adjustment)/Printer color balance adjustment (Auto adjustment) (Color model) | ||
| 48 | 1 | Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direction). | |
| 5 | Used to correction the scan image magnification ratio (in the sub scanning direction). | Scanner section | |
| 6 | Used to adjust the rotation speed of each motor. | ||
| 49 | 1 | Used to perform the firmware update. | |
| 3 | Used to update the operation manual in the HDD. | ||
| 50 | 1 | Copy image position, image loss adjustment | |
| 2 | Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SIM 50-1). | ||
| 5 | Used to adjust the print lead edge image position. (PRINTER MODE) | ||
| 6 | Used to adjust the copy image position and the image loss. (DSPF mode) | DSPF | |
| 7 | Used to adjust the copy image position and the image loss (DSPF mode). (This simulation is a simplified version of SIM 50-6.) | DSPF | |
| 10 | Used to adjust the black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) | ||
| 12 | Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) | ||
| 20 | Image registration adjustment (Manual adjustment) | ||
| 22 | Used to adjust the image registration. (Main scan direction, sub scan direction) (Auto adjustment)/OPC drum phase adjustment (Auto adjustment) (Only color model) |
||
| 24 | Used to display the detail data of SIM 44-2, 50-20 and 22. | ||
| 27 | Used to perform the image loss adjustment of scanned images in the FAX or image send mode. | ||
| 28 | Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio. | ||
| 51 | 1 | Used to adjust the ON/OFF timing of the secondary transport voltage. (Only color model) | |
| 2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the DSPF registration roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) | ||
| 53 | 8 | Used to adjust the document lead edge reference and the DSPF mode document scan position. | |
| 55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
| 2 | Used to set the specifications of the scanner control operation. (SOFT SW) | ||
| 3 | Used to set the specifications of the controller operation. (SOFT SW) | ||
| 56 | 1 | Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) | |
| 2 | Used to backup the data in the EEPROM. SRAM, and HDD (including user authentication data and address data) to the USB memory. (Corresponding to the device cloning and the storage backup.) | ||
| 3 | Used to backup the document filling data to the USB memory. | ||
| 4 | Used to backup the JOB log data to the USB memory. | ||
| 60 | 1 | Used to check the operations (read/write) of the MFP PWB memory. | |
| 2 | Used to set the MFP PWB on-board SDRAM. | ||
| 61 | 1 | Used to check the LSU polygon motor rotation and laser detection. | LSU |
| 3 | Used to set the laser power | ||
| 4 | Used to print the print image skew adjustment pattern. (LSU unit) | ||
| 62 | 1 | Used to execute the hard disk format (except operation manual area). | |
| 2 | Used to check read/write of the hard disk (partial). | ||
| 3 | Used to check read/write of the hard disk (all areas). | ||
| 6 | Used to perform the self diagnostics of the hard disk. | ||
| 7 | Used to print the hard disk self diagnostics error log. | ||
| 8 | Used to format the hard disk. (Excluding the system area and the operation manual area) | ||
| 10 | Used to delete the job log data. | ||
| 11 | Used to delete the document filing data. | ||
| 12 | Used to set Enable/Disable of auto format in a hard disk trouble. | ||
| 13 | Used to format the hard disk. (only the operation manual area) |