Sharp MXC382SC
Simulation mode. Codes Color model 43-46
Main | Sub | Functions | Section |
---|---|---|---|
43 | 1 | Used to set the fusing reference temperature of each operation mode. | |
4 | Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.) | ||
20 | Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-1) in each paper mode. | ||
21 | Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-1) in each paper mode. | ||
22 | Used to set the environment correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-4) in each paper mode. | ||
23 | Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-4) in each paper mode. | ||
24 | Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4. | ||
44 | 1 | Used to set each correction operation function in the image forming (process) section. | Image process (Photo-conductor/Developing/ Transfer/Cleaning) |
2 | Used to adjust the sensitivity of the image density sensor (registration sensor). | Process | |
4 | Used to set the conditions of the high density process control operation. | Process | |
6 | Used to execute the high density process control forcibly. | Process | |
9 | Used to display the result data of the high density process control operation. | Image process (Photo-conductor/Developing/ Transfer/Cleaning) |
|
12 | Used to display the operation data of the high density process control and the image density sensor (registration sensor). | Image process (Photo-conductor/Developing) |
|
13 | Used to perform the color image sensor (image registration sensor F) calibration. (Only color model) | ||
14 | Used to display the output level of the temperature and humidity sensor. | Process (OPC drum, development)/Fusing/LSU | |
16 | Used to display the toner density control data. | Developing system | |
21 | Used to set the half tone process control target. | Process | |
22 | Used to display the toner patch density level in the half tone process control operation. | Process | |
24 | Used to display the correction target and the correction level in the half tone process control operation. | Process | |
25 | Used to set the calculating conditions of the correction value for the half tone process control. | Process | |
26 | Used to execute the half tone process control compulsorily. | Process | |
27 | Used to clear the correction data of the half tone process control. | Process | |
28 | Used to set the process control execution conditions. | Process | |
29 | Used to set the operating conditions of the process control during a job. | Process | |
31 | Used to adjust the OPC drum phase. (Manual adjustment) (Only color model) | Process | |
37 | Used to set the development bias correction level in the continuous printing operation. | ||
43 | Used to display the identification information of the developing unit. | Developing system | |
61 | Used to set the calibration data of the color image sensor (image registration sensor F). (Only color model) | ||
46 | 1 | Used to adjust the copy density in the copy mode. (Only color model) | |
2 | Used to adjust the copy density in the copy mode. | ||
4 | Used to adjust the density in the image send mode. | ||
5 | Used to adjust the density in the image send mode. | ||
8 | Used to adjust the image send mode color balance RGB. | ||
9 | Used to adjust the scan image density. | ||
10 | Used to adjust the copy color balance and the gamma (for each color copy mode). (Only color model) | ||
16 | Used to adjust the monochrome copy density and the gamma (for each monochrome copy mode). | ||
19 | Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode documents. | ||
21 | Copy color balance adjustment (Manual adjustment) (Color model) | ||
23 | Used to set the density correction of copy high density section (High density tone gap supported). | ||
24 | Copy color balance adjustment (Auto adjustment) (Color model) | ||
25 | Used to adjust the copy color balance. (Single color copy mode) (Only color model) | ||
26 | Used to reset the single color mode color balance set value to the default. (Only color model) | ||
27 | Used to adjust the gamma/density of copy images, texts, and line image edges. (Only color model) | ||
30 | Used to adjust the resolution in the sub scanning direction in the copy mode. (Only color model) | ||
32 | Used to adjust the document background density reproducibility in the monochrome auto copy mode. | ||
36 | Used to adjust the colors in the 2-color copy mode. (Only color model) | ||
37 | Used to adjust the color document reproducibility in the monochrome copy mode. | ||
38 | Used to adjust the black component amount in the color copy mode. (Only color model) | ||
39 | Used to adjust the sharpness of FAX send images. | ||
40 | Used to adjust the FAX send image density. (Collective adjustment of all the modes) | ||
41 | Used to adjust the FAX send image density. (Normal) | ||
42 | Used to adjust the FAX send image density. (Fine) | ||
42 | Used to adjust the FAX send image density. (Fine) | ||
44 | Used to adjust the FAX send image density. (Ultra fine) | ||
45 | Used to adjust the FAX send image density. (600dpi). | ||
47 | Used to set the compression rate of copy and scan images (JPEG). | ||
51 |
Used to adjust the gamma for the copy mode heavy paper mode and the image process mode. (Manual adjustment) |
|