Sharp MXC382SC
Simulation mode. Codes Color model 1-22
Main | Sub | Functions | Section |
---|---|---|---|
1 | 1 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) |
2 | Used to check the sensors in the scanner (reading) section and the related circuits. | Scanner (reading) | |
5 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) | |
2 | 1 | Used to check the operations of the auto document feed unit and the control circuit. | DSPF |
2 | Used to check the operations of the sensors and the detectors in the document feed unit section and the control circuits. | DSPF | |
3 | Used to check the operations of the loads in the auto document feed unit and the control circuit. | DSPF | |
3 | 2 | Used to check the operations of the sensors and the detectors in the finisher and the control circuit. | Finisher |
3 | Used to check the operation of the load in the finisher and the control circuit. | Finisher | |
10 | Used to adjust the finisher. | Finisher | |
4 | 2 | Used to check the operations of the sensors and detectors in the paper feed tray, and the control circuit of those. | Paper feed tray (Option) |
3 | Used to check the operations of the loads in the paper feed tray, and the control circuit of those. | Paper feed tray | |
5 | Used to check the operations of the paper feed tray unit paper transport clutch (DTRC). | Paper feed tray unit | |
5 | 1 | Used to check the operation of the display, LCD in the operation panel, and control circuit. | Operation panel |
2 | Used to check the operation of the heater lamp and the control circuit. | Fusing | |
3 | Used to check the operation of the scanner lamp and the control circuit. | Scanner (reading) | |
4 | Used to check the operation of the discharge lamp and the control circuit. | Process | |
6 | 1 | Used to check the operations of the load in the paper transport system (clutches and solenoids) and the control circuits. | Paper transport/Paper exit section |
2 | Used to check the operations of each fan motor and its control circuit. | Others | |
3 | Used to check the operations of the primary transfer unit and the control circuit. | Process (Transfer) | |
6 | Used to check the operation of the fusing separation. (Only color model) | Fusing | |
51 | Used to forcibly cut down the initial fuse of the developer unit and the fusing unit. | Developing, fusing unit | |
7 | 1 | Used to set the operating conditions of aging. | Others |
6 | Used to set the operating intermittent aging cycle. | ||
8 | Used to display the warm-up time. | ||
9 | Color setting in the color copy test mode (Used to check the copy operation and the image quality for each color). (Only color model) | ||
12 | The document reading number of sheets setting (for aging operation) | DSPF | |
8 | 1 | Used to check and adjust the operations of the developing voltage in each print mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. |
Process (Developing) |
2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. |
Process (Charging) | |
6 | Used to check and adjust the operation of the transfer voltage and the control circuit. | Process (Transport) | |
9 | 2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit. | Duplex |
3 | Used to check the operations of the load in the switchback section (duplex section) and its control circuit. | Duplex | |
10 | 1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit. | Process (Developing) |
13 | - | Used to cancel the self-diag "U1" trouble. | |
14 | - | Used to cancel the self-diag H3, H4, H5 troubles. | |
16 | - | Used to cancel the self-diag "U2" trouble. | MFP PWB / PCU PWB / SCU PWB |
17 | - | Used to cancel the self-diag "PF" trouble. | |
21 | 1 | Used to set the maintenance cycle. | |
22 | 1 | Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) | |
2 | Used to check the total numbers of mis-feed and troubles. (When the number of total jam is considerably great, it is judged as necessary for repair.) | ||
3 | Used to check mis-feed positions and the mis-feed count of each position. * Presumption of the faulty point by this data is possible. |
||
4 | Used to check the trouble (self diag) history. | ||
5 | Used to check the ROM version of each unit (section). | Firmware | |
6 | Used to output various adjustment/setting data (simulations, FAX soft switch counter), the firmware version, the counter list, the process control data, and SIM50-24 data. | ||
8 | Used to check the number of operations (counter value) of the finisher, the DSPF, and the scan (reading) unit. | ||
9 | Used to check the number of use (print quantity) of each paper feed section. | Paper feed, ADU | |
10 | Used to check the system configuration (option, internal hardware). | ||
11 | Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) | FAX | |
12 | Used to check the DSPF mis-feed positions and the number of mis-feed at each position. (When the number of mis-feed is considerably great, it can be judged as necessary for repair.) | DSPF | |
13 | Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge). | Process | |
19 | Used to check the values of the counters related to the scan - image send. | ||
90 | Used to output the various set data lists. |