Main |
Sub |
Functions |
Section |
62 |
1 |
Used to execute the hard disk format (except operation manual area). |
|
2 |
Used to check read/write of the hard disk (partial). |
|
3 |
Used to check read/write of the hard disk (all areas). |
|
6 |
Used to perform the self diagnostics of the hard disk. |
|
7 |
Used to print the hard disk self diagnostics error log. |
|
8 |
Used to format the hard disk. (Excluding the system area and the operation manual area) |
|
10 |
Used to delete the job log data. |
|
11 |
Used to delete the print hold data (document filing data). (4.3 Inch LCD model) |
|
11 |
Used to delete the document filing data. (8.5 Inch LCD model) |
|
12 |
Used to set Enable/Disable of auto format in a hard disk trouble. |
|
13 |
Used to format the hard disk. (only the operation manual area) |
|
63 |
1 |
Used to display the shading correction result. |
Scanner |
2 |
Used to perform shading. |
|
3 |
Used to perform scanner (CCD) color balance and gamma auto adjustment. |
Scanner |
4 |
Used to display the SIT chart patch density. |
|
5 |
Used to perform the scanner (CCD) color balance and gamma default setting. |
|
6 |
Used to display the scan level and the density level of the copy color balance adjustment patch. |
|
7 |
Used to register the service target of the copy mode auto color balance adjustment. |
|
8 |
Used to set the default of the service target of the copy mode auto color balance adjustment. |
|
11 |
Used to set the target color balance of the copy mode auto color balance adjustment. |
|
64 |
1 |
Test print. (Self print) (Color mode) |
|
2 |
Test print. (Self print) (Monochrome mode) |
|
4 |
Printer test print. (Self print) (256 gradations) |
|
5 |
Printer test print. (Self print) (PCL) |
|
6 |
Printer test print. (Self print) (PS) |
|
7 |
Used to print the adjustment pattern of the test print. (Self print). (The adjustment pattern of SIM46-21 is printed.) |
|
65 |
1 |
Used to adjust the touch panel (LCD display section) detection coordinates. (8.5 Inch LCD model only) |
Operation panel section |
2 |
Used to display the touch panel (LCD display section) detection coordinates. (8.5 Inch LCD model only) |
|
5 |
Used to check the operation panel key input. |
|
67 |
17 |
Used to reset the printer controller. |
Printer |
24 |
Printer color balance adjustment (Auto adjustment) |
Printer |
25 |
Printer color balance adjustment (Manual adjustment) |
Printer |
26 |
Used to set the target color balance of the printer mode auto color balance adjustment. |
Printer |
27 |
Used to set the service target of the printer mode auto color balance adjustment. |
Printer |
28 |
Used to set the default of the service target of the printer mode auto color balance adjustment. |
Printer |
31 |
Used to clear the printer calibration value. |
Printer |
33 |
Used to change the gamma of the printer screen. (for PCL/PS) |
Printer |
34 |
Used to set the density correction in the printer high density section. (Support for the high density section tone gap) |
Printer |
36 |
Used to adjust the density in the low density section. |
Printer |
52 |
Used to reset the printer color balance adjustment (adjustment for each dither) to the default value. (The set values of SIM67-54 and SIM67-33 are set to the default values.) |
|
54 |
Printer color balance adjustment (Automatic adjustment for each dither) |
|
70 |
MFP PWB SRAM data clear |
MFP PWB |