| Main |
Sub |
Functions |
Section |
| 43 |
1 |
Used to set the fusing reference temperature of each operation mode. |
|
| 4 |
Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.) |
|
| 20 |
Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-1) in each paper mode. |
|
| 21 |
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-1) in each paper mode. |
|
| 22 |
Used to set the environment correction under low temperature and low humidity (L/L) for the fusing temperature setting (SIM 43-4) in each paper mode. |
|
| 23 |
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing temperature setting (SIM 43-4) in each paper mode. |
|
| 24 |
Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4. |
|
| 44 |
1 |
Used to set each correction operation function in the image forming (process) section. |
Image process (Photo-conductor/ Developing/Transfer/Cleaning) |
| 2 |
Used to adjust the sensitivity of the image density sensor (registration sensor). |
Process |
| 4 |
Used to set the conditions of the high density process control operation. |
Process |
| 6 |
Used to execute the high density process control forcibly. |
Process |
| 9 |
Used to display the result data of the high density process control operation. |
Image process (Photo-conductor/ Developing/Transfer/Cleaning) |
| 12 |
Used to display the operation data of the high density process control and the image density sensor (registration sensor). |
Image process (Photo-conductor/ Developing) |
| 13 |
Used to perform the color image sensor (image registration sensor F) calibration. |
|
| 14 |
Used to display the output level of the temperature and humidity sensor. |
Process (OPC drum, development)/Fusing/LSU |
| 16 |
Used to display the toner density control data. |
Developing system |
| 21 |
Used to set the halftone process control target. |
Process |
| 22 |
Used to display the toner patch density level in the halftone process control operation. |
Process |
| 24 |
Used to display the correction target and the correction level in the halftone process control operation. |
Process |
| 25 |
Used to set the calculating conditions of the correction value for the halftone process control. |
Process |
| 26 |
Used to execute the halftone process control compulsorily. |
Process |
| 27 |
Used to clear the correction data of the halftone process control. |
Process |
| 28 |
Used to set the process control execution conditions. |
Process |
| 29 |
Used to set the operating conditions of the process control during a job. |
Process |
| 31 |
Used to adjust the OPC drum phase. (Manual adjustment) (MX-C400P/C380P) |
Process |
| 37 |
Used to set the development bias correction level in the continuous printing operation. |
|
| 43 |
Used to display the identification information of the developing unit. |
Developing system |
| 61 |
Used to set the calibration data of the color image sensor (image registration sensor F). |
|
| 46 |
21 |
Copy color balance adjustment (Manual adjustment) |
|
| 48 |
6 |
Used to adjust the rotation speed of each motor. |
|
| 49 |
1 |
Used to perform the firmware update. |
|
| 3 |
Used to update the operation manual in the HDD. |
|
| 50 |
1 |
Print image position, image loss adjustment |
|
| 5 |
Used to adjust the print lead edge image position. (PRINTER MODE) |
|
| 10 |
Used to adjust the black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) |
|
| 20 |
Image registration adjustment (Manual adjustment) |
|
| 22 |
Used to adjust the image registration. (Main scan direction, sub scan direction) (Auto adjustment)/OPC drum phase adjustment (Auto adjustment) |
|
| 24 |
Used to display the detail data of SIM 44-2, 50-20 and 22. |
|
| 51 |
1 |
Used to adjust the ON/OFF timing of the secondary transport voltage. |
|
| 2 |
Used to adjust the contact pressure (deflection amount) on paper by the resist roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper or when paper jams frequently occur.) |
|
| 55 |
1 |
Used to set the specifications of the engine control operations. (SOFT SW) |
|
| 3 |
Used to set the specifications of the controller operation. (SOFT SW) |
|
| 56 |
1 |
Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) |
|
| 2 |
Used to backup the data in the EEPROM. SRAM, and HDD to the USB memory. (Corresponding to the device cloning and the storage backup.) |
|
| 3 |
Used to backup the print hold data (document filling data) to the USB memory. |
|
| 4 |
Used to backup the JOB log data to the USB memory. |
|
| 60 |
1 |
Used to check the operations (read/write) of the MFP PWB memory. |
|
| 2 |
Used to set the MFP PWB on-board SDRAM. |
|
| 61 |
1 |
Used to check the LSU polygon motor rotation and laser detection. |
LSU |
| 3 |
Used to set the laser power |
|
| 4 |
Used to print the print image skew adjustment pattern. (LSU unit) |
|