Sharp MXB355WZ
Simulation mode. List of classic mode. Codes 66-1 - 67-54
| Sim No. | Function | Easy Mode | ||
|---|---|---|---|---|
| Installation | Maintenance | Adjustment and Settings | ||
| 66-1 | Set the specification of image send operation | 2-3 | ||
| 66-2 | Set country code | |||
| 66-3 | Check FAX PWB memory | |||
| 66-4 | Check signal output level (max) | |||
| 66-5 | Check signal output level (soft SW) | |||
| 66-6 | Used to print the confidential registration check table | |||
| 66-7 | Used to output all image data saved in the image memory | |||
| 66-8 | Used to send the selected sound message to the line and the speaker (max) | |||
| 66-9 | Used to send the selected sound message to the line and the speaker (soft SW) | |||
| 66-10 | Used to clear the FAX and image send image data | |||
| 66-11 | Used to send the selected signal at 300bps to the line and the speaker (max) | |||
| 66-12 | Used to send the selected signal at 300bps to the line and the speaker (soft SW) | |||
| 66-13 | Used to register dial number for Sim66-14/ 15/16 dial test | |||
| 66-14 | Used to excute the dial pulse (10pps) send test and to adjust the make time | |||
| 66-15 | Used to excute the dial pulse (20pps) send test and to adjust the make time | |||
| 66-16 | Used to execute the DTMF signal send test and to adjust the send level | |||
| 66-17 | Used to send the DTMF signal to the line and the speaker (max) | |||
| 66-18 | Used to send the DTMF signal to the line and the speaker (soft SW) | |||
| 66-21 | Used to print the selected iyems (system error, protocol monitor) | |||
| 66-29 | Used to intialize the telephone book data | |||
| 66-30 | Used to display the TEL/LIU status change, the display is highlighted by status change | |||
| 66-31 | Used to set ON/OFF the port for output to TEL/LIU | |||
| 66-32 | Used to check the fixed data received from the line and to display the result | |||
| 66-33 | Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected the display is highlighted | |||
| 66-36 | Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the command line individually |
|||
| 66-39 | Used to check and change the destination setting saved in EEPROM of the FAX | |||
| 66-42 | Used to rewrite the program to power control installed in the FAX | |||
| 66-43 | Used to write the adjustment value into the power control installed in the FAX | |||
| 66-61 | Set the specification of image send operation | |||
| 66-62 | Backup FAX received data to the USB memory | |||
| 67-17 | Reset printer memory | |||
| 67-24 | Adjust printer gray balance (auto) | 6 | ||
| 67-25 | Adjust printer gray balance (manual) | 1-4 | 6 | |
| 67-26 | Set gray balance target in the printer mode | 6 | ||
| 67-31 | Clear printer calibration data | |||
| 67-33 | Adjust printer screen gamma | |||
| 67-34 | Set the density correction of printer high density area | |||
| 67-36 | Adjust the density in the printer low density area |
|||
| 67-46 | Adjust printer image edge | |||
| 67-52 | Set gamma default value of the printer screen |
1-3 | ||
| 67-54 | Adjust printer gray balance | 1-3 | ||