Sharp MXB355WZ
Simulation mode. List of classic mode. Codes 26-32 - 46-51
Sim No. | Function | Easy Mode | ||
---|---|---|---|---|
Installation | Maintenance | Adjustment and Settings | ||
26-32 | Set the fusing cleaning operation | |||
26-33 | Special function setting | |||
26-35 | Set SIM22-4 trouble history when a same trouble occurred repeatedly as one trouble or several time | |||
26-38 | Set print operation when the maintenance life is reached | |||
26-41 | Set auto magnification ratio select function in the center binding mode | |||
26-49 | Set the print speed in postcard mode | |||
26-50 | Set the function | 2-1 | ||
26-52 | Set count mode of blank paper | 2-2 | ||
26-65 | Set finisher alarm mode | 2-1 | ||
26-66 | Set simulation password | |||
26-69 | Set toner near end operating condition | 2-4 | ||
26-73 | Adjust image enlargement and A3 wide copy | |||
26-74 | Set OSA trial mode | |||
26-78 | Set remote operation panel password | 2-1 | ||
26-79 | Set security function | |||
26-85 | Set simulation function | |||
27-2 | Set FSS sender's registration number and host server number | 2-5 | ||
27-4 | Set FSS initial mode and toner order timing | 2-5 | ||
27-5 | Set machine tag No | |||
27-6 | Set manual service call | |||
27-7 | Set FSS function and alert | 2-5 | ||
27-9 | Set FSS paper transport time recording and alert | 2-5 | ||
27-10 | Clear trouble prediction history | |||
27-11 | Check serial communication retry number and scanner gain adjustment retry number history | |||
27-12 | Check high density and halftone process control error history | |||
27-13 | Check history of paper transport time between sensors | |||
27-14 | Set FSS connection test mode | 2-5 | ||
27-15 | Check FSS connection status | 2-5 | ||
27-16 | Set FSS alert function | 2-5 | ||
30-1 | Check the operation of the sensors in other than the paper feed section and the control circuit | |||
30-2 | Check the operation of the sensors in the paper feed section and the control circuit | |||
43-1 | Set the fusing temperature in each mode | |||
43-2 | Set the fusing operation and preheat mode | |||
43-20 | Set the fusing temperature in each mode (environment correction under low temperature and low humidity of Sim43-2) | |||
43-21 | Set the fusing temperature in each mode (environment correction under high temperature and high humidity of Sim43-2) | |||
43-24 | Set the fusing operation | |||
43-35 | Check fusing unit pressure state | |||
44-1 | Set each correction operation function in the image forming section | |||
44-2 | Set the sensitivity of the image density sensor |
2-2 2-3 |
2 | |
44-6 | Execute the high density process control forcibly | 1-5 | 2-3 | |
44-9 | Check the high density process control operation data | |||
44-12 | Check the high density process control and the image density sensor operation data | |||
44-14 | Check the output level of the temperature and humidity sensor | |||
44-15 | Set the OPC drum idle rotation | |||
44-17 | Execute refresh operation of the developer and transfer roller | |||
44-21 | Set the halftone process control target | 5 | ||
44-22 | Check the toner patch density level in the halftone process control operation | |||
44-24 | Check the correction target and the correction level in the halftone process control operation | |||
44-25 | Set the calculating conditions of the correction value for the halftone process control | |||
44-26 | Execute the halftone process control forcibly | 1-5 | 2-3 | |
44-27 | Clear the correction data of the halftone process control | |||
44-28 | Set the process control execution condition | |||
44-29 | Set the operating condition of the halftone process control | |||
44-37 | Set the developer bias correction level in the continuous printing operation | |||
44-43 | Check the identification information of the developing unit | |||
44-62 | Set the process control execution condition | |||
46-2 | Adjust the copy density in the copy mode | |||
46-4 | Adjust the color scan density in the image send mode | |||
46-5 | Adjust the monochrome scan density in the image send mode | |||
46-8 | Adjust the color balance RGB in the image send mode | |||
46-9 | Adjust the scan image density (SPF) | 3 | ||
46-10 | Adjust the copy gray balance and gamma (for each copy mode) | |||
46-16 | Adjust the copy gray balance and gamma (for all mode) | 1-3 | 5 | |
46-19 | Set the scanning operating condition of the document density in the auto mode | |||
46-23 | Set the density correction of copy high density area (for high density tone gap) | |||
46-24 | Adjust copy gray balance (auto adjustment) | 5 | ||
46-32 | Adjust the document background density reproducibility in the auto mode | |||
46-37 | Adjust the reproducibility capability of gray image creation | |||
46-39 | Adjust the sharpness of send image | |||
46-40 | Adjust the FAX send image density (all modes) | |||
46-41 | Adjust the FAX send image density (normal) | |||
46-42 | Adjust the FAX send image density (fine) | |||
46-43 | Adjust the FAX send image density (super fine) | |||
46-44 | Adjust the FAX send image density (ultra fine) | |||
46-45 | Adjust the FAX send image density (600dpi) | |||
46-46 | Adjust the FAX send image density (RGB RIP) | |||
46-47 | Set the compression ratio of copy and scan images (JPEG) | |||
46-48 | Set the copy output resolution in the copy mode | |||
46-51 | Adjust the gamma of heavy paper mode and image process mode in the copy mode |