Sharp MXB355WZ
Simulation mode. List of classic mode. Codes 1-1 - 26-30
| Sim No. | Function | Easy Mode | ||
|---|---|---|---|---|
| Installation | Maintenance | Adjustment and Settings | ||
| 1-1 | Check the operation of the scanner (reading) unit and the control circuit | |||
| 1-2 | Check the sensors in the scanner (reading) section and the related circuit | |||
| 1-5 | Check the operation of the scanner (reading) unit and the control circuit | |||
| 2-1 | Check the operation of the auto document feeder and the control circuit | |||
| 2-2 | Check the operation of the sensors in the auto document feeder section and the control circuit | |||
| 2-3 | Check the operation of the loads in the auto document feeder and the control circuit | |||
| 3-2 | Check the operation of the sensors in the finisher and the control circuit | |||
| 3-3 | Check the operation of the loads in the finisher and the control circuit | |||
| 3-10 | Adjust the finisher | 4 | ||
| 4-2 | Check the operation of the sensors in the desk/large capacity tray (LCC) and the control circuit | |||
| 4-3 | Check the operation of the loads in the desk/large capacity tray (LCC) and the control circuit | |||
| 4-5 | Check the operation of the clutch in the desk/large capacity tray (LCC) | |||
| 5-1 | Check the operation of the display, LCD in the operation panel and the control circuit | |||
| 5-2 | Check the operation of the heater lamp and the control circuit | |||
| 5-3 | Check the operation of the scanner lamp and the control circuit | |||
| 5-4 | Check the operation of the discharge lamp and the control circuit | |||
| 6-1 | Check the operation of the loads in the paper transport system (clutches and solenoids) and the control circuit | |||
| 6-2 | Check the operation of the each fan motor and the control circuit | |||
| 6-90 | Set default position back to the factory setting (scanner is set to the lock enable position) | 6 | ||
| 7-1 | Set the operating condition of aging | |||
| 7-6 | Set the operating intermittent aging cycle | |||
| 7-8 | Check the warm up time | |||
| 7-12 | Set the document reading number of sheets (for aging operation) | |||
| 8-1 | Check and adjust the operation of the developping voltage in each print mode and the control circuit | |||
| 8-2 | Check and adjust the operation of the main charger voltage in each print mode and the control circuit | |||
| 8-6 | Check and adjust the operation of the transport voltage and the control circuit | |||
| 9-2 | Check the operation of the sensors in the paper reverse section (duplex section) and the control circuit | |||
| 9-3 | Check the operation of the loads in the paper reverse section (duplex section) and the control circuit | |||
| 10-1 | Check the operation of the toner supply mechanism (toner motor) and the control circuit | |||
| 10-4 | Toner cartridge motor count sensor check | |||
| 13 | Cancel U1 trouble | 5 | 6 | |
| 14 | Cancel H3, H4, H5 trouble | 5 | 6 | |
| 16 | Cancel U2 trouble | 5 | 6 | |
| 21-1 | Set maintenance cycle | 4 | ||
| 22-1 | Check the print count value in each section and each operation mode | 3-1 | 1-1 | 9-1 |
| 21-2 | Check the total number of misfeed and trouble |
|||
| 21-3 | Check misfeed ppositions and misfeed count of each position | 1-2 | ||
| 21-4 | Check the trouble history | |||
| 21-5 | Check the firmware version of each unit | 3-2 | 1-3 | 9-2 |
| 21-6 | Output setting/adjustment data, firmware version and counter list | 3-3 | 1-4 | 9-3 |
| 21-8 | Check the number of operation (counter value) of the finisher, SPF and scan (reading) unit | 1-1 | ||
| 21-9 | Check the number of use (print counter) of each paper feed section | 3-1 | 1-1 | 9-1 |
| 21-10 | Check the system configuration | 3-2 | 1-3 | 9-2 |
| 21-11 | Check FAX counter | |||
| 21-12 | Check SPF misfeed positions and number of misfeed at each position | 1-2 | ||
| 21-13 | Check the operation time of the process section (Drum unit, DV unit, toner cartridge) and fusing unit | 3-1 | 1-1 | 9-1 |
| 21-14 | Check the use status of the toner cartridge | |||
| 21-18 | Check user data clear history | |||
| 21-19 | Check counter value of scan, image send mode | |||
| 21-40 | Check trouble code information | |||
| 21-41 | Check JAM code information | |||
| 21-42 | Check JAM, trouble data | |||
| 21-43 | Check JAM history data | |||
| 21-90 | Output system setting list | |||
| 23-2 | Output JAM, trouble history data | 3-3 | 1-4 | 9-3 |
| 23-80 | Check the operation of paper feed and paper transport in the paper feed section and paper transport section and output the list of the operation status of the sensor in the paper feed section and paper transport section | |||
| 23-81 | Export paper feed time list | |||
| 24-1 | Clear JAM counter and trouble counter | 3 | ||
| 24-2 | Clear paper feed counter of each paper feed section | 3 | ||
| 24-3 | Clear SPF, scan (reading) and finisher counter | 3 | ||
| 24-4 | Clear maintenance counter and print counter of the transport unit and the fusing unit | 3 | ||
| 24-5 | Clear developer counter | |||
| 24-35 | Clear used toner cartridge counter | |||
| 25-1 | Check the operation of the developing section | |||
| 25-2 | Set toner density initial level when replacing developer | 2-2 2-5 |
2 | |
| 25-4 | Check toner supply control data | |||
| 25-5 | Check toner density correction data | |||
| 25-10 | Set developer/drum serial no | |||
| 26-2 | Size setup | 2-1 | ||
| 26-3 | Set the specification of the auditor | 2-1 | ||
| 26-6 | Set the destination | |||
| 26-7 | Set the machine ID | |||
| 26-10 | Set the trial mode of the network scanner | |||
| 26-18 | Set the toner save mode | 2-4 | ||
| 26-30 | Set the operation mode corresponding to CE control | |||