Sharp MX5051
Simulation mode. List of Classic mode. Codes 08 - 26
| Main | Sub | Functions | Section |
|---|---|---|---|
| 8 | 1 | Used to check and adjust the operations of the developing voltage in each print mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Developing) |
| 2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Charging) | |
| 6 | Used to check and adjust the operation of the transport voltage and the control circuit. | Process (Transport) | |
| 10 | Main charger total current output setting | Process | |
| 9 | 2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit. |
Duplex |
| 3 | Used to check the operations of the load in the paper reverse section (duplex section) and its control circuit. | Duplex | |
| 10 | 1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit. | Toner supply section |
| 2 | Used to check the operations of the toner remaining quantity sensor and the control circuit. | Toner supply section | |
| 13 | - | Used to cancel the self-diag "U1" trouble. | |
| 14 | - | Used to cancel the self-diag H3, H4, H5 troubles. | |
| 15 | - | Used to cancel the self-diag "U6" trouble. | LCC/LCT |
| 16 | - | Used to cancel the self-diag "U2" trouble. | MFP PWB / PCU PWB / SCU PWB |
| 21 | 1 | Used to set the maintenance cycle. | |
| 22 | 1 | Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) | |
| 2 | Used to check the total number of misfeed and troubles. (When the number of total jam is considerably great, it is judged as necessary for repair.) | ||
| 3 | Used to check misfeed positions and the misfeed count of each position. * Presumption of the faulty point by this data is possible. |
||
| 4 | Used to check the trouble (self diag) history. | ||
| 5 | Used to check the ROM version of each unit (section). | Firmware | |
| 6 | Used to output the setting/adjustment data (simulation, FAX soft switch, counter), the firmware version, and the counter list. | ||
| 8 | Used to check the number of operations (counter value) of the finisher, the DSPF, and the scan (reading) unit. | ||
| 9 | Used to check the number of use (print quantity) of each paper feed section. | Paper feed, ADU, LCC | |
| 10 | Used to check the system configuration (option, internal hardware). | ||
| 11 | Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) | FAX | |
| 12 | Used to check the DSPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) | DSPF | |
| 13 | Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the fusing unit | Process | |
| 14 | Used to display the use status of the toner cartridge. | Process | |
| 18 | Used to display the user data delete history. | ||
| 19 | Used to check the values of the counters related to the scan - image send. | ||
| 40 | Used to display the error code list and the contents. | ||
| 41 | Used to check JAM code information. | ||
| 42 | Used to check the JAM/trouble data. | ||
| 43 | JAM data details display | ||
| 90 | Used to output the various set data lists. | ||
| 23 | 2 | Used to output the trouble history list of paper jam and misfeed. (If the number of troubles of misfeed is considerably great, the judgment is made that repair is required.) | |
| 80 | Used to check the operation of paper feed and paper transport in the paper feed section and the paper transport section. Used to output the list of the operation status of the sensor and the detectors in the paper feed section and the paper transport section. | Paper feed, Paper transport | |
| 81 | Used to export paper feed time list. | ||
| 24 | 1 | Used to clear the jam counter, and the trouble counter. (After completion of maintenance, clear the counters.) | |
| 2 | Used to clear the number of use (the number of prints) of each paper feed section. | ||
| 3 | Used to clear the finisher, DSPF, and the scan (reading) unit counter. | ||
| 4 | Used to clear the maintenance counter, the printer counters of the transport unit and the fusing unit. (After completion of maintenance, clear the counters.) |
||
| 5 | Used to clear the developer counter value and the toner hopper remaining quantity counter. (After replacing developer, clear these counters.) |
||
| 35 | Used to clear the toner cartridge use status data. | ||
| 25 | 1 | Used to check the operations of the developing section. | Process (Developing section) |
| 2 | Used to make the initial setting of toner density when replacing developer. (Automatic adjustment) | Image process (Photoconductor/ Developing/Transfer/Cleaning) | |
| 4 | Used to display the operation data of the toner supply quantity. (Not used in the market.) | Process | |
| 5 | Used to display the toner density correction data. (Not used in the market.) | Process | |
| 10 | Developer/drum serial number setting | ||
| 26 | 1 | Used to set Yes/No of installation of the right paper exit tray. | Paper exit |
| 2 | Used to set the paper size of the large capacity tray (LCC). (When the paper size is changed, this simulation must be executed to change the paper size in software.) | Paper feed | |
| 3 | Used to set the specifications of the auditor. (Setting must be made according to the auditor use conditions.) |
Auditor | |
| 5 | Used to set the count mode of the total counter and the maintenance counter. (A3/11x17 size) | ||
| 6 | Used to set the specifications (paper, fixed magnification ratio, etc.) of the destination. | ||
| 7 | Used to set the machine ID. | ||
| 8 | Counter mode setting (Long scale) | ||
| 18 | Used to set Disable/Enable of the toner save mode operation. (For the Japan and the UK versions.) | ||
| 30 | Used to set the operation mode corresponding to the CE mark (Europe safety standards). (For slow start to drive the fusing heater lamp) |