Sharp MX5050N
Simulation mode. List of Classic mode. Codes 66 - 67
Sim No. | Easy Mode | ||||
---|---|---|---|---|---|
Installation | Maintenance | Adjustment and Settings | |||
66 | 7 | Used to output all image data saved in the image memory | |||
8 | Used to send the selected sound message to the line and the speaker (send level: max) | ||||
9 | Used to send the selected sound message to the line and the speaker (send level: soft SW setting) | ||||
10 | Used to clear the FAX and image send image data | ||||
11 | Used to send the selected signal at 300bps to the line and the speaker (send level: max) | ||||
12 | Used to send the selected signal at 300bps to the line and the speaker (send level: soft SW setting) | ||||
13 | Used to register dial number for Sim66-14/ 15/16 dial test | ||||
14 | Used to execute the dial pulse (10pps) send test and to adjust the make time | ||||
15 | Used to execute the dial pulse (20pps) send test and to adjust the make time | ||||
16 | Used to execute the DTMF signal send test and to adjust the send level | ||||
17 | Used to send the DTMF signal to the line and the speaker (send level: max) | ||||
18 | Used to send the DTMF signal to the line and the speaker (send level: soft SW setting) | ||||
21 | Used to print the selected items (system error, protocol monitor) | ||||
22 | Used to set the handset sound volume (Japan model only) | ||||
29 | Used to initialize the telephone book data and FAX system error | ||||
30 | Used to display the TEL/LIU status change, the display is highlighted by status change | ||||
31 | Used to set ON/OFF the port for output to TEL/LIU | ||||
32 | Used to check the fixed data received from the line and to display the result | ||||
33 | Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected the display is highlighted | ||||
36 | Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the command line individually | ||||
39 | Used to check and change the destination setting saved in EEPROM of the FAX BOX | ||||
42 | Used to rewrite the program to power control installed in the FAX BOX | ||||
43 | Used to write the adjustment value into the power control installed in the FAX BOX | ||||
61 | Used to display the image send-related soft SW (151-250) on the LCD to allow changing the soft SW while checking with the LCD | ||||
62 | Used to import the FAX receive data into a USB memory in PDF file type | ||||
67 | 17 | Printer reset | |||
24 | Printer color balance adjustment (Auto adjustment) | 6 | |||
25 | Printer color balance adjustment (Manual adjustment) | 1-4 | 6 | ||
26 | Used to set the target color balance of the printer mode auto color balance adjustment | 6 | |||
27 | Used to set the service target of the printer mode auto color balance adjustment | 6 | |||
28 | Used to set the default of the service target of the printer mode auto color adjustment | 6 | |||
31 | Used to clear the printer calibration value | ||||
33 | Used to change the gamma of the printer screen |
||||
34 | Used to set the density correction in the printer high density section | ||||
36 | Used to adjust the density in the low density section | ||||
41 | Used to set 2 color print | ||||
42 | Used to set 2 color print color density | ||||
43 | Used to adjust 2 color mode color balance | ||||
52 | Used to set the default of the gamma of the printer screen | 1-3 | |||
54 | Printer color balance adjustment | 1-3 |