Sharp MX5050N
Simulation mode. List of Classic mode. Codes 01 - 10
| Sim No. | Easy Mode | ||||
|---|---|---|---|---|---|
| Installation | Maintenance | Adjustment and Settings | |||
| 1 | 1 | Used to check the operation of the scanner (reading) unit and the control circuit | |||
| 2 | Used to check the sensors in the scanner (reading) section and the related circuit | ||||
| 5 | Used to check the operation of the scanner (reading) unit and the control circuit | ||||
| 2 | 1 | Used to check the operations of the automatic document feeder and the control circuit |
|||
| 2 | Used to check the operations of the sensors and the detectors in the automatic document feeder section and the control circuit |
||||
| 3 | Used to check the operations of the loads in the automatic document feeder and the control circuit |
||||
| 3 | 2 | Used to check the operations of the sensors and the detectors in the finisher and the control circuit |
|||
| 3 | Used to check the operation of the load in the finisher and the control circuit | ||||
| 10 | Used to adjust the finisher | 4 | |||
| 4 | 2 | Used to check the operations of the sensors and detectors in the desk/large capacity tray (LCC) and the control circuit of those | |||
| 3 | Used to check the operations of the loads in the desk/large capacity tray (LCC) and the control circuit of those | ||||
| 5 | Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper transport clutch (LTRC) | ||||
| 5 | 1 | Used to check the operation of the display, LCD in the operation paper and the control circuit | |||
| 2 | Used to check the operation of the heater lamp and the control circuit | ||||
| 3 | Used to check the operation of the scanner lamp and the control circuit | ||||
| 4 | Used to check the operation of the discharge lamp and the control circuit | ||||
| 6 | 1 | Used to check the operations of the load in the paper transport system (clutches and solenoids) and the control circuit | |||
| 2 | Used to check the operations of each fan motor and its control circuit | ||||
| 3 | Used to check the operations of the transport unit and the control circuit | ||||
| 4 | Used to check the cleaning of the main charger | ||||
| 6 | Used to perform fusing pressure release and applying and to check the operations of the control circuit | ||||
| 90 | Used to reset the machine to the factory setting (The scanner is set to the lock enable position) | ||||
| 7 | 1 | Used to set the operating conditions of aging | |||
| 6 | Used to set the operating intermittent aging cycle | ||||
| 8 | Used to display the warm up time | ||||
| 9 | Color setting in the color copy test mode (used to check the copy operation and the image quality for each color) | ||||
| 12 | The document reading number of sheets (for aging operation) | ||||
| 8 | 1 | Used to check and adjust the operations of the developping voltage in each print mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | |||
| 2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | ||||
| 6 | Used to check and adjust the operation of the transport voltage and the control circuit | ||||
| 10 | Main charger current output setting | ||||
| 9 | 2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit | |||
| 3 | Used to check the operations of the load in the paper reverse section (duplex section) and its control circuit | ||||
| 10 | 1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit | |||