Sharp MX3640N
Simulation mode. List of simulation codes 46 - 56
| Main | Sub | Functions | Section |
|---|---|---|---|
| 46 | 32 | Used to adjust the document background density reproducibility in the monochrome auto copy mode. | |
| 36 | Used to adjust the colors in the 2-color copy mode. | ||
| 37 | Used to adjust the reproduction capability of monochrome mode color. | ||
| 38 | Used to adjust the black component amount in the color copy mode. | ||
| 39 | Used to adjust the sharpness of FAX send images. | ||
| 40 | Used to adjust the FAX send image density. (Collective adjustment of all the modes) | ||
| 41 | Used to adjustthe FAX send image density. (Normal) | ||
| 42 | Used to adjust the FAX send image density. (Fine) | ||
| 43 | Used to adjust the FAX send image density. (Super Fine) | ||
| 44 | Used to adjust the FAX send image density. (Ultra fine) | ||
| 45 | Used to adjust the FAX send image density. (600dpi). | ||
| 46 | Used to adjust the FAX send image density. (RGB RIP) | ||
| 47 | Used to set the compression rate of copy and scan images (JPEG). | ||
| 51 | Used to adjust the gamma for the copy mode heavy paper mode and the image process mode. | ||
| 52 | Used to set the gamma default for the copy mode heavy paper and the image process mode. (After execution of either SIM46-54 or SIM46-51, the adjustment value is reset to the initial value.) |
||
| 54 | Used to perform the engine halftone automatic density adjustment (dither). | ||
| 55 | Used to adjust the drop out color in the image send mode (monochrome manual text mode). | ||
| 58 | Used to set the copy mode pseudo resolution. (Smoothing process) | ||
| 59 | Used to perform the copy mode pseudo resolution image process adjustment. | ||
| 60 | Used to adjust the sharpness in the color auto copy mode. | ||
| 61 | Used to adjust the area separation recognition level. | ||
| 62 | Used to set the operating conditions of the ACS, the area separation, the background image process, and the auto exposure mode. | ||
| 63 | Used to adjust the density in the copy low density section. | ||
| 65 | Used to set the color correction table. | ||
| 66 | Used to adjust the reproduction capability of watermarks in the copy/printer mode. | ||
| 74 | Copy color balance adjustment (Auto adjustment)/Printer color balance adjustment (Auto adjustment) | ||
| 90 | Used to set the process operation of high-compression PDF images. | ||
| 91 | Used to adjust the reproduction capability of black text. | ||
| 48 | 1 | Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direction). | |
| 5 | Used to correction the scan image magnification ratio (in the sub scanning direction). | Scanner section | |
| 6 | Used to adjust the rotation speed of each motor. | ||
| 49 | 1 | Used to perform the firmware update. | |
| 3 | Used to update the operation manual in the HDD. | ||
| 5 | Used to perform the watermark update. | ||
| 10 | Used to perform the ACU firmware update. | ||
| 50 | 1 | Copy image position, image loss adjustment | |
| 5 | Used to adjust the print lead edge image position. (PRINTER MODE) | ||
| 6 | Used to adjust the copy image position and the image loss. (RSPF mode) | RSPF | |
| 10 | Used to adjustthe black print image magnification ratio and the off-center position. (The adjustment is made separately for each paper feed section.) |
||
| 12 | Used to perform the scan image off-center position adjustment. (The adjustment is made separately for each scan mode.) |
||
| 20 | Image registration adjustment (Main scanning direction) | ||
| 22 | Used to adjustthe image registration. (Main scan direction, sub scan direction) (Auto adjustment)/OPC drum phase adjustment (Auto adjustment) |
||
| 24 | Used to display the detail data of SIM 44-2, 50-20 and 22. | ||
| 27 | Used to perform the image loss adjustment of scanned images in the FAX or image send mode. | ||
| 28 | Used to automatically adjustthe image loss, void area, image off-center, and image magnification ratio. | ||
| 51 | 1 | Used to adjust the ON/OFF timing of the secondary transport voltage. | |
| 2 | Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF resist roller. (This adjustment is performed when there is a considerable variation in the print image position on the paper orwhen paper jams frequently occur.) | ||
| 53 | 6 | Used to adjust the detection level of the RSPF document width. | |
| 7 | Used to adjust the RSPF document size width sensor. | ||
| 8 | Used to adjust the document lead edge reference and the RSPF mode document scan position. | ||
| 9 | RSPF dirt detection setting | ||
| 10 | RSPF dirt detection execution | ||
| 55 | 1 | Used to set the specifications of the engine control operations. (SOFT SW) | |
| 2 | Used to set the specifications of the scanner control operation. (SOFT SW) | ||
| 3 | Used to set the specifications ofthe controller operation. (SOFT SW) | ||
| 10 | Used to set the special stamp text. (Taiwan only) | ||
| 56 | 1 | Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.) | |
| 2 | Used to backup the data in the EEPROM. SD Card, and HDD (including user authentication data and address data) to the USB memory. (Corresponding to the device cloning and the storage backup.) | ||
| 3 | Used to backup the document filing data to the USB memory. | ||
| 4 | Used to backup the JOB log data to the USB memory. | ||
| 5 | Used to import the SIM22-6 data to a USB memory in the TEXT format. | ||
| 6 | Used to import the SIM23-2 data into a USB memory in the TEXT format. | ||
| 7 | Used to import SYSLOG data into a USB memory |