Sharp MX3631
Simulation mode. List of Classic mode. Codes 48-1 - 61-4
| Sim No. | Function | Installation | Maintenance | Adjustment and Settings |
|---|---|---|---|---|
| 48-1 | Adjust the scan image magnification ratio (Main scanning direction and Sub scanning direction) | 1-1 | ||
| 48-5 | Adjust the scan image magnification ratio (Sub scanning direction) | 1-1 | ||
| 48-6 | Adjust the rotation speed of each motor | |||
| 49-1 | Update the firmware | 4 | 5 | |
| 49-7 | Update the pre-installed firmware | 4 | 5 | |
| 50-1 | Adjust the Copy image position and the image loss | 1-1 | ||
| 50-5 | Adjust the print lead edge image position in the printer mode | 1-1 | ||
| 50-6 | Adjust the copy image position and the image loss (SPF) | 1-1 | ||
| 50-10 | Adjust the black print image magnification ratio and the off center position | 1-2 | 2-1 | 1-1 |
| 50-12 | Adjust the scan image off center position | 1-1 | ||
| 50-20 | Adjust image registration (Manual) | 1-2 | ||
| 50-22 | Adjust the image registration (Main scan direction, sub scan direction) (Auto) / OPC drum phase (Auto) | 1-1 | 2-1 | 1-1 1-2 |
| 50-23 | Set the registration correction | |||
| 50-24 | Display the detailed data of SIM 44-2, 50-20, 21 and 22 | |||
| 50-27 | Adjust the image loss of scanned images in the FAX and image send mode | |||
| 51-1 | Adjust the ON/OFF timing of the secondary transfer voltage | |||
| 51-2 | Adjust the contact pressure (deflection amount) on paper by the main unit and the SPF resist roller | |||
| 53-6 | Adjust the detection level of the SPF document width | 3 | ||
| 53-7 | Adjust the SPF document size width sensor | |||
| 53-8 | Adjust the document lead edge reference and the SPF mode document scan position | 3 | ||
| 53-9 | Set scanning position in SPF | |||
| 53-10 | Execute dirt detection in SPF | |||
| 55-1 | Set the specification of the engine control operations (SOFT SW) | |||
| 55-2 | Set the specification of the scanner control operation (SOFT SW) | |||
| 55-3 | Set the specification of the controller operation (SOFT SW) | |||
| 55-10 | Set the special stamp text (For Taiwan) | |||
| 56-1 | Transport data between STORAGE - MFP EEPROM | |||
| 56-2 | Store the data in the EEPROM, ICU DRIVE and STORAGE to the USB memory | |||
| 56-3 | Store the document filing data to the USB memory | |||
| 56-4 | Store the JOB log data to the USB memory | |||
| 56-5 | Store the SIM22-6 data to the USB memory in the text format | |||
| 56-6 | Store the SIM23-2 JAM/trouble data to the USB memory in the text format | |||
| 56-7 | Store the system log data to the USB memory | |||
| 56-8 | Update ICC profile | |||
| 56-15 | Restore the data for the MFP EEPROM | |||
| 56-99 | Store all log data to the USB memory | 3-4 | 1-5 | 9-4 |
| 60-1 | Check the memory operations (read/write) of the SCN MFP PWB | |||
| 61-1 | Check the LSU polygon motor rotation and laser detection | |||
| 61-3 | Set the laser power | |||
| 61-4 | Print out the print image skew adjustment pattern |