Sharp MX3570N
Simulation mode. List of Classic mode. Codes 01 - 16
| Sim No. | Easy Mode | |||
|---|---|---|---|---|
| Installation | Maintenance | Adjustment and Settings | ||
| 1-1 | Used to check the operation of the scanner (reading) unit and the control circuit | |||
| 1-2 | Used to check the sensors in the scanner (reading) section and the related circuit | |||
| 1-5 | Used to check the operation of the scanner (reading) unit and the control circuit | |||
| 2-1 | Used to check the operations of the automatic document feeder and the control circuit | |||
| 2-2 | Used to check the operations of the sensors and the detectors in the automatic document feeder section and the control circuit |
|||
| 2-3 | Used to check the operations of the loads in the automatic document feeder and the control circuit |
|||
| 3-2 | Used to check the operations of the sensors and the detectors in the finisher and the control circuit |
|||
| 3-3 | Used to check the operation of the load in the finisher and the control circuit | |||
| 3-10 | Used to adjust the finisher | 4 | ||
| 4-2 | Used to check the operations of the sensors and detectors in the desk/large capacity tray (LCC) and the control circuit of those | |||
| 4-3 | Used to check the operations of the loads in the desk/large capacity tray (LCC) and the control circuit of those | |||
| 4-5 | Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper transport clutch (LTRC) | |||
| 5-1 | Used to check the operation of the display, LCD in the operation paper and the control circuit |
|||
| 5-2 | Used to check the operation of the heater lamp and the control circuit | |||
| 5-3 | Used to check the operation of the scanner lamp and the control circuit | |||
| 5-4 | Used to check the operation of the discharge lamp and the control circuit | |||
| 6-1 | Used to check the operations of the load in the paper transport system (clutches and solenoids) and the control circuit | |||
| 6-2 | Used to check the operations of each fan motor and its control circuit | |||
| 6-3 | Used to check the operations of the transport unit and the control circuit | |||
| 6-6 | Used to perform fusing pressure release and applying and to check the operations of the control circuit | |||
| 6-90 | Used to reset the machine to the factory setting (The scanner is set to the lock enable position) | 6 | ||
| 7-1 | Used to set the operating conditions of aging | |||
| 7-6 | Used to set the operating intermittent aging cycle | |||
| 7-8 | Used to display the warm up time | |||
| 7-9 | Color setting in the color copy test mode (used to check the copy operation and the image quality for each color) | |||
| 7-12 | The document reading number of sheets (for aging operation) | |||
| 8-1 | Used to check and adjust the operations of the developping voltage in each print mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | |||
| 8-2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. *When the middle speed is adjusted the low speed are also adjusted simultaneously | |||
| 8-6 | Used to check and adjust the operation of the transport voltage and the control circuit | |||
| 8-10 | Main charger current output setting | |||
| 9-2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit | |||
| 9-3 | Used to check the operations of the load in the paper reverse section (duplex section) and its control circuit | |||
| 10-1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit | |||
| 10-3 | Used to check the ejector position sensor | 6 | 2-5 | 2 |
| 13 | Used to cancel the self-diag U1 trouble | 5 | 6 | |
| 14 | Used to cancel the self-diag H3, H4, H5 troubles | 5 | 6 | |
| 15 | Used to cancel the self-diag U6 trouble | 5 | 6 | |
| 16 | Used to cancel the self-diag U2 trouble | 5 | 6 | |