Sharp MX3111U
Simulation mode. List of simulation codes 65 - 67
| Main | Sub | Functions | Section |
|---|---|---|---|
| 65 | 1 | Used to adjust the touch panel (LCD display section) detection coordinates. | Operation panel section |
| 2 | Used to display the touch panel (LCD display section) detection coordinates. | ||
| 5 | Used to check the operation panel key input. | ||
| 66 | 1 | Used to display the FAX-related soft SW (2 - 150) on the LCD to allow changing the soft SW while checking with the LCD. | FAX |
| 2 | Used to enter a country code and set the default value for the country code. | FAX | |
| 3 | Used to check read/write of the EEPROM and the SDRAM on the MODEM controller and display the result. | FAX | |
| 4 | Used to send the selected signals to the line and the main unit speaker. (Send level: max.) | FAX | |
| 5 | Used to send the selected signal to the line and the main unit speaker. (Send level: Soft SW setting) (For the kinds of send signals, refer to SIM66-04.) |
FAX | |
| 6 | Used to print the confidential registration check table (BOX NO., BOX name, passcode. (If there is no confidential registration, no print is made.) | FAX | |
| 7 | Used to output all image data saved in the image memory. (Confidential data are also outputted.) | FAX | |
| 8 | Used to send the selected sound messages to the line and the speaker. (Send level: Max.) | FAX | |
| 9 | Used to send the selected sound message to the line and the speaker. (Send level: Soft SW setting) * For details of sound messages, refer to the sound message table of SIM66-08. |
FAX | |
| 10 | Used to clear the FAX and image send image data. (The confidential data are also cleared.) | FAX | |
| 11 | Used to send the selected signal at 300bps to the line and the speaker. (Send level: Max.) | FAX | |
| 12 | Used to send the selected signal at 300bps to the line and the speaker. (Send level: Soft SW setting) * For the kings of send signals at 300bps, refer to SIM66-11,300bps send signal table. |
FAX | |
| 13 | Used to register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be registered.) | FAX | |
| 14 | Used to execute the dial pulse (10PPS) send test and to adjust the make time. | FAX | |
| 15 | Used to execute the dial pulse (20PPS) send test and to adjust the make time. | FAX | |
| 16 | Used to execute the DTFM signal send test and to adjust the send level. | FAX | |
| 17 | Used to send the DTMF signal to the line and the speaker. (Send level: Max.) | FAX | |
| 18 | Used to send the DTMF signal to the line and the speaker. (Send level: Soft SW setting) | FAX | |
| 21 | Used to print the selected items (system error, protocol monitor). | FAX | |
| 22 | Used to set the handset sound volume. (This simulation can be executed even though the handset setting is set to NO. When, however, the handset is not installed, the sound volume cannot be checked.) (Japan model only) | FAX | |
| 24 | Used to clear the FAST save data. | FAX | |
| 29 | Used to initialize the telephone book data (the one-touch registration table, the FTP/Desktop expansion table, the group expansion table, the program registration table, the interface memory box table, the meta data, InboundRouting, and the DocumentAdmin table). | FAX | |
| 30 | Used to display the TEL/LIU status change, The display is highlighted by status change. | FAX | |
| 31 | Used to set ON/OFF the port for output to TEL/LIU. | FAX | |
| 32 | Used to check the fixed data received from the line and to display the result. | FAX | |
| 33 | Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected, the display is highlighted. | FAX | |
| 34 | Used to execute the send test and display the time required for sending image data in the test. Used to execute send test and display. (Unit: ms) | FAX | |
| 36 | Used to check send and receive data from the MODEM controller to the MFP controller or the data line or the command line individually. | FAX | |
| 39 | Used to check and change the destination setting saved in EEPROM of the FAX BOX. | FAX | |
| 42 | Used to rewrite the program to power control installed in the FAX BOX. | FAX | |
| 43 | Used to write the adjustment value into the power control installed in the FAX BOX. | FAX | |
| 61 | Used to display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft SW while checking with the LCD. | FAX | |
| 62 | Used to import the FAX receive data into a USB memory in PDF file type. | FAX | |
| 67 | 17 | Printer reset | Printer |
| 24 | Printer color balance adjustment (Auto adjustment) | Printer | |
| 25 | Printer color balance adjustment (Manual adjustment) | Printer | |
| 26 | Used to set the target color balance of the printer mode auto color balance adjustment. | Printer | |
| 27 | Used to set the service target of the printer mode auto color balance adjustment. | Printer | |
| 28 | Used to set the default of the service target of the printer mode auto color balance adjustment. | Printer | |
| 31 | Used to clear the printer calibration value. | Printer | |
| 33 | Used to change the gamma of the printer screen. | Printer | |
| 34 | Used to set the density correction in the printer high density section. (Support for the high density section tone gap) | Printer | |
| 36 | Used to adjust the density in the low density section. | Printer | |
| 45 | Used to adjust the printer image filter and trapping. | Printer | |
| 52 | Used to set the default of the gamma of the printer screen. | Printer | |
| 54 | Printer color balance adjustment (Automatic adjustment for each dither (The adjustment is disable in a GDI printer.)) | Printer |