Sharp MX3111U
Simulation mode. List of simulation codes 01 - 22
| Main | Sub | Functions | Section |
|---|---|---|---|
| 1 | 1 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) |
| 2 | Used to check the sensors in the scanner (reading) section and the related circuits. | Scanner (reading) | |
| 5 | Used to check the operation of the scanner (reading) unit and the control circuit. | Scanner (reading) | |
| 2 | 1 | Used to check the operations of the automatic document feeder and the control circuit. | RSPF |
| 2 | Used to check the operations of the sensors and the detectors in the automatic document feeder section and the control circuits. | RSPF | |
| 3 | Used to check the operations of the loads in the automatic document feeder and the control circuit. | RSPF | |
| 3 | 2 | Used to check the operations of the sensors and the detectors in the finisher and the control circuit. | Finisher |
| 3 | Used to check the operation of the load in the finisher and the control circuit. | Finisher | |
| 10 | Used to adjust the finisher. | Finisher | |
| 4 | 2 | Used to check the operations of the sensors and detectors in the desk/large capacity tray (LCC), and the control circuit of those. | Desk/Large capacity tray (LCC) |
| 3 | Used to check the operations of the loads in the desk/large capacity tray (LCC), and the control circuit of those. | Desk/Large capacity tray (LCC) | |
| 5 | Used to check the operations of the paper feed desk paper transport clutch (DTRC) and the LCC paper transport clutch (LTRC). | Desk/Large capacity tray (LCC) | |
| 5 | 1 | Used to check the operation of the display, LCD in the operation panel, and control circuit. | Operation panel |
| 2 | Used to check the operation of the heater lamp and the control circuit. | Fusing | |
| 3 | Used to check the operation of the scanner lamp and the control circuit. | Scanner (reading) | |
| 4 | Used to check the operation of the discharge lamp and the control circuit. | Process | |
| 6 | 1 | Used to check the operations of the load in the paper transport system (clutches and solenoids) and the control circuits. | Paper transport/Paper exit section |
| 2 | Used to check the operations of each fan motor and its control circuit. | Others | |
| 3 | Used to check the operations of the transport unit and the control circuit. | Process (Transport) | |
| 6 | Used to perform fusing pressure release and applying, and to check the operations of the control circuits. | Fusing | |
| 90 | Used to reset the machine to the factory setting. (The scanner is set to the lock enable position) | Scanner | |
| 7 | 1 | Used to set the operating conditions of aging. | Others |
| 6 | Used to set the operating intermittent aging cycle. | ||
| 8 | Used to display the warm-up time. | ||
| 9 | Color setting in the color copy test mode (Used to check the copy operation and the image quality for each color). | ||
| 12 | The document reading number of sheets setting (for aging operation) | RSPF | |
| 8 | 1 | Used to check and adjust the operations of the developing voltage in each print mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Developing) |
| 2 | Used to check and adjust the operation of the main charger grid voltage in each printer mode and the control circuit. * When the middle speed is adjusted, the low speed are also adjusted simultaneously. | Process (Charging) | |
| 6 | Used to check and adjust the operation of the transport voltage and the control circuit. | Process (Transport) | |
| 9 | 2 | Used to check the operations of the sensors and detectors in the paper reverse section (duplex section) and its control circuit. | Duplex |
| 3 | Used to check the operations of the load in the paper reverse section (duplex section) and its control circuit. | Duplex | |
| 10 | 1 | Used to check the operations of the toner supply mechanism (toner motor) and the related circuit. | Process (Developing) |
| 13 | - | Used to cancel the self-diag "U1" trouble. | |
| 14 | - | Used to cancel the self-diag H3, H4, H5 troubles. | |
| 15 | - | Used to cancel the self-diag "U6" trouble. | LCC |
| 16 | - | Used to cancel the self-diag "U2" trouble. | MFP PWB / PCU PWB / SCU PWB |
| 17 | - | Used to cancel the self-diag "PF" trouble. | |
| 21 | 1 | Used to set the maintenance cycle. | |
| 22 | 1 | Used to check the print count value in each section and each operation mode. (Used to check the maintenance timing.) |
|
| 2 | Used to check the total number of misfeed and troubles. (When the number of total jam is considerably great, it is judged as necessary for repair.) |
||
| 3 | Used to check misfeed positions and the misfeed count of each position. * Presumption of the faulty point by this data is possible. |
||
| 4 | Used to check the trouble (self diag) history. | ||
| 5 | Used to check the ROM version of each unit (section). | Firmware | |
| 6 | Used to output the setting/adjustment data (simulation, FAX soft switch, counter), the firmware version, and the counter list. | ||
| 8 | Used to check the number of operations (counter value) of the finisher, the RSPF, and the scan (reading) unit. | ||
| 9 | Used to check the number of use (print quantity) of each paper feed section. | Paper feed, ADU, LCC | |
| 10 | Used to check the system configuration (option, internal hardware). | ||
| 11 | Used to check the use frequency (send/receive) of FAX. (Only when FAX is installed) | FAX | |
| 12 | Used to check the RSPF misfeed positions and the number of misfeed at each position. (When the number of misfeed is considerably great, it can be judged as necessary for repair.) | RSPF | |
| 13 | Used to check the operating time of the process section (OPC drum, DV unit, toner cartridge) and the fusing unit | Process | |
| 14 | Used to display the use status of the toner cartridge. | Process |