| Sim No. |
Function |
| 43 |
1 |
Set the fusing temperature in each mode |
| |
2 |
Set the fusing operation and preheat mode |
| |
20 |
Set the fusing temperature in each mode (environment correction under low temperature and low humidity of Sim43-2) |
| |
21 |
Set the fusing temperature in each mode (environment correction under high temperature and high humidity of Sim43- 2) |
| |
24 |
Set the fusing operation |
| |
35 |
Check fusing unit pressure state |
| 44 |
1 |
Set each correction operation function in the image forming section |
| 2 |
Set the sensitivity of the image density sensor |
| 4 |
Used to set the conditions of the high density process control operation. |
| 6 |
Execute the high density process control forcibly |
| 9 |
Check the high density process control operation data |
| 12 |
Check the high density process control and the image density sensor operation data |
| 14 |
Check the output level of the temperature and humidity sensor |
| 15 |
Set the OPC drum idle rotation |
| 17 |
Execute refresh operation of the developer and transfer roller |
| 21 |
Set the halftone process control target |
| 22 |
Check the toner patch density level in the halftone process control operation |
| 24 |
Check the correction target and the correction level in the halftone process control operation |
| 25 |
Set the calculating conditions of the correction value for the halftone process control |
| 26 |
Execute the halftone process control forcibly |
| 27 |
Clear the correction data of the halftone process control |
| 28 |
Set the process control execution condition |
| 29 |
Set the operating condition of the halftone process control |
| 37 |
Set the developer bias correction level in the continuous printing operation |
| 43 |
Check the identification information of the developing unit |
| 62 |
Set the process control execution condition |
| 46 |
16 |
Adjust the copy gray balance and gamma (for all mode) |
| 48 |
6 |
Adjust the rotation speed of each motor |
| 49 |
1 |
Update the firmware |
| 50 |
1 |
Adjust the copy image position and the image loss |
| 5 |
Adjust the printer image position and the image loss |
| 10 |
Adjust the image position in the each paper feed tray |
| 51 |
1 |
Set the transfer voltage timing |
| 2 |
Adjust the contact pressure on paper by the main unit and the SPF resist roller |
| 55 |
1 |
Set the specification of the engine operation |
| 3 |
Set the specification of the controller operation |
| 56 |
2 |
Backup the data in the EEPROM and STORAGE to the USB memory |
| 5 |
Backup the SIM22-6 data in the text format to the USB memory |
| 60 |
1 |
Check read/write memory operation |
| 61 |
1 |
Check the LSU polygon motor rotation and laser detection |
| 3 |
Set the laser power |
| 64 |
2 |
Test print |
| 4 |
Printer test print |
| 5 |
Printer test print (PCL) |
| 6 |
Printer test print (PS) |
| 65 |
10 |
KEY time setting display |
| 67 |
22 |
Adjust image balance |
| 23 |
Test Print |
| 25 |
Adjust printer gray balance (manual) |
| 31 |
Clear printer calibration data |
| 33 |
Adjust printer screen gamma |
| 34 |
Set the density correction of printer high density area |
| 36 |
Adjust the density in the printer low density area |
| 52 |
Set gamma default value of the printer screen |