| Sim No. |
Function |
| 46 |
24 |
Adjust copy gray balance (auto adjustment) |
| 32 |
Adjust the document background density reproducibility in the auto mode |
| 37 |
Adjust the reproducibility capability of gray image creation |
| 39 |
Adjust the sharpness of send image |
| 40 |
Adjust the FAX send image density (all modes) |
| 41 |
Adjust the FAX send image density (normal) |
| 42 |
Adjust the FAX send image density (fine) |
| 43 |
Adjust the FAX send image density (super fine) |
| 51 |
Adjust the gamma of heavy paper mode and image process mode in the copy mode |
| 52 |
Set gamma default value of heavy paper mode and image process mode in the copy mode |
| 54 |
Adjust the engine halftone auto density (dither) |
| 48 |
1 |
Adjust the scan image magnification ratio (main scanning direction and sub scanning direction) |
| 6 |
Adjust the rotation speed of each motor |
| 49 |
1 |
Update the firmware |
| 50 |
1 |
Adjust the copy image position and the image loss |
| 5 |
Adjust the printer image position and the image loss |
| 6 |
Adjust SPF image position and the image loss |
| 10 |
Adjust the image position in the each paper feed tray |
| 12 |
Adjust the scan image off center position |
| 51 |
1 |
Set the transfer voltage timing |
| 2 |
Adjust the contact pressure on paper by the main unit and the SPF resist roller |
| 53 |
8 |
Adjust the document lead edge and the scan position |
| 9 |
Set the dirt detection and scan position |
| 10 |
Execute SPF dirt detection |
| 55 |
1 |
Set the specification of the engine operation |
| 2 |
Set the specification of the scanner operation |
| 3 |
Set the specification of the controller operation |
| 10 |
Used to set the special stamp text for Taiwan |
| 56 |
2 |
Backup the data in the EEPROM and STORAGE to the USB memory |
| 5 |
Backup the SIM22-6 data in the text format to the USB memory |
| 60 |
1 |
Check read/write memory operation |
| 61 |
1 |
Check the LSU polygon motor rotation and laser detection |
| 3 |
Set the laser power |
| 63 |
1 |
Check shading correction data |
| 2 |
Execute shading correction |
| 3 |
Adjust scanner (CCD) color balance and gamma correction |
| 5 |
Reset the scanner (CCD) color balance and gamma correction |
| 12 |
B/W image create adjustment |
| 64 |
2 |
Test print |
| 4 |
Printer test print |
| 5 |
Printer test print (PCL) |
| 6 |
Printer test print (PS) |
| 65 |
10 |
KEY time setting display |
| 66 |
1 |
Set the specification of image send operation |
| 2 |
Set country code |
| 4 |
Check signal output level (max) |
| 7 |
Used to output all image data saved in the image memory |
| 8 |
Used to send the selected sound message to the line and the speaker (max) |
| 10 |
Used to clear the FAX and image send image data |
| 11 |
Used to send the selected signal at 300bps to the line and the speaker (max) |
| 13 |
Used to register dial number for Sim66-14/15/16 dial test |
| 17 |
Used to send the DTMF signal to the line and the speaker (max) |
| 21 |
Used to print the selected iyems (system error, protocol monitor) |
| 30 |
Used to display the TEL/LIU status change, the display is highlighted by status change |
| 31 |
Used to set ON/OFF the port for output to TEL/LIU |
| 32 |
Used to check the fixed data received from the line and to display the result |
| 33 |
Used to execute detection of various signals with the line connected and to display the detection result. When a signal is detected the display is highlighted |
| 34 |
Communication time display |
| 66 |
52 |
Pseudo ringer check |
| 67 |
25 |
Adjust printer gray balance (manual) |
| 31 |
Clear printer calibration data |
| 33 |
Adjust printer screen gamma |
| 34 |
Set the density correction of printer high density area |
| 36 |
Adjust the density in the printer low density area |
| 52 |
Set gamma default value of the printer screen |