| Sim No. |
Function |
| 24 |
5 |
Clear developer counter |
| 35 |
Clear used toner cartridge counter |
| 25 |
1 |
Check the operation of the developing section |
| 2 |
Set toner density initial level when replacing developer |
| 4 |
Check toner supply control data |
| 5 |
Check toner density correction data |
| 26 |
6 |
Set the destination |
| 7 |
Set the machine ID |
| 18 |
Set the toner save mode |
| 30 |
Set the operation mode corresponding to CE control |
| 35 |
Set SIM22-4 trouble history when a same trouble occurred repeatedly as one trouble or several time |
| 38 |
Set print operation when the maintenance life is reached |
| 41 |
Set auto magnification ratio select function in the center binding mode |
| 49 |
Set the print speed in postcard mode |
| 50 |
Set the function |
| 54 |
LCD duty setting |
| 65 |
Set finisher alarm mode |
| 66 |
Set simulation password |
| 69 |
Set toner near end operating condition |
| 73 |
Adjust image enlargement and A3 wide copy |
| 74 |
Set OSA trial mode |
| 78 |
Set remote operation panel password |
| 79 |
Set security function |
| 85 |
Set simulation function |
| 30 |
1 |
Check the operation of the sensors in other than the paper feed section and the control circuit |
| 43 |
1 |
Set the fusing temperature in each mode |
| 2 |
Set the fusing operation and preheat mode |
| 20 |
Set the fusing temperature in each mode (environment correction under low temperature and low humidity of Sim43-2) |
| 21 |
Set the fusing temperature in each mode (environment correction under high temperature and high humidity of Sim43- 2) |
| 24 |
Set the fusing operation |
| 35 |
Check fusing unit pressure state |
| 44 |
1 |
Set each correction operation function in the image forming section |
| 2 |
Set the sensitivity of the image density sensor |
| 4 |
Used to set the conditions of the high density process control operation. |
| 6 |
Execute the high density process control forcibly |
| 9 |
Check the high density process control operation data |
| 12 |
Check the high density process control and the image density sensor operation data |
| 14 |
Check the output level of the temperature and humidity sensor |
| 15 |
Set the OPC drum idle rotation |
| 17 |
Execute refresh operation of the developer and transfer roller |
| 21 |
Set the halftone process control target |
| 22 |
Check the toner patch density level in the halftone process control operation |
| 24 |
Check the correction target and the correction level in the halftone process control operation |
| 25 |
Set the calculating conditions of the correction value for the halftone process control |
| 26 |
Execute the halftone process control forcibly |
| 27 |
Clear the correction data of the halftone process control |
| 28 |
Set the process control execution condition |
| 29 |
Set the operating condition of the halftone process control |
| 37 |
Set the developer bias correction level in the continuous printing operation |
| 43 |
Check the identification information of the developing unit |
| 62 |
Set the process control execution condition |
| 46 |
2 |
Adjust the copy density in the copy mode |
| 4 |
Adjust the color scan density in the image send mode |
| 5 |
Adjust the monochrome scan density in the image send mode |
| 9 |
Adjust the scan image density (SPF) |
| 16 |
Adjust the copy gray balance and gamma (for all mode) |
| 19 |
Set the scanning operating condition of the document density in the auto mode |
| 23 |
Set the density correction of copy high density area (for high density tone gap) |